CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP EDGE
HAZARD.
BATTERY IS INCLUDED AND MUST BE CONNECTED; see instructions 23 - 25
1 •Place from bumper on body and tighten four screws as shown in the drawing.
2 •Place rear bumper on body.
3 •Tighten three screws as shown in the drawing.
4 •Assemble the two parts of the steering wheel.
5 •Place the horn in the steering wheel’s central hole, following the instructions in its packaging.
6 •Insert the steering wheel on the steering wheel column.
7 •Align steering wheel column holes with steering wheel: nut fits into haxagon hole, bolt into round hole.
8 •Insert the windscreen.
9 •Secure it by means of the two screws.
10 •Place seat on body. Adjust seat position. Secure it with washer and thumb nut.
11 •Join A to part B of the Roll-Bar.
12 •join A-B to the upper section of the Roll-Bar C, insert and rotate to secure.
13 •Insert the 2 plates in the slots at the base of the Roll-Bar and hold them in place. Secure the plates and the Roll-Bar with the 2 screws
provided (detail A).
14 •Insert the end of the safety belt in the slot situated centrally in the bottom of the seat, as shown in the figure.
15 •Screw the net down to the body.
16 •Snap it around the roll-bar as shown in the drawing.
17 •Insert the rearview mirrors in the direction shown by the arrow.
18 •Apply the corresponding stickers to the 2 sides of the body (see sticker sheet), then press the two plastic writings into position.
19 •Insert the antenna, pressing down as you do so, into its appropriate housing, situated on the right rear mudguard.
20 •Remove the radio from its packaging. Unscrew the cover from the battery chamber. Insert two 1.5 Volt AA batteries (not supplied with the
vehicle) into the compartment, taking care to position the positive and negative poles correctly. Close the battery compartment cover and
screw into place.
21 •Insert the wire from the antenna and the radio into their appropriate housing on the dashboard, making sure to place them the right way up,
as shown in the figure.
22 •Snap fit the four hub covers onto the wheels.
BATTERY INSTALLATION
WARNING:
WARNING: BATTERY CHARGING AND ANY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY ADULTS ONLY.
THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM THE VEHICLE.
23 •Open the bonnet by turning the 2 side fasteners and remove the screw on the grill.
24 •Plug battery terminal A into vehicle wiring terminal B.
25 •Close the bonnet by turning the 2 side fasteners and tighten the screw.
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
26 •Below the box you can find four removable toy tools. To remove the box, pull out and unfasten the four couplings.
27 •A: HORN. Push the yellow button the horn will sound.
B: FM RADIO: a real removable car radio that works independently. Press button 3 to turn it on. Press button 4 to turn it off. Use the
triangular buttons to change the frequency with automatic tuning. The station will not be memorized when the radio is turned off. Use knob
2 to adjust the volume. To adjust the time, hold down the SET button and push the HR and MIN buttons as appropriate.
The AUX (1) socket on the radio can be used for connecting MP3 devices.
C: SIMULATED START-KEY. The key provided is only a “toy key”, and does not turn the vehicle on or off.
D: Accelerator/electric brake pedal. The electric braking system stops the vehicle automatically when your child lifts his foot off the pedal.
28 •To unfasten the safety belts:1 push towards the middle and simultaneously press the button; 2 detach the buckle.
29 •GEAR SHIFT LEVERS: 1: first speed. 2: second speed. R: reverse.
30 •SECOND SPEED: When the red lock-out is positioned as shown in the figure, the vehicle will run in first speed and reverse only. The turtle
on the lock-out is in the up position. To use the second gear, follow the instructions: loose the screw on the red lock-out.
31 •Remove the red lock-out.
32 •Rotate it 180° until the hare is in the up position. Insert the lock-out into the hole provided.
33 •Tighten the screw. By pushing the gearshift lever backward, the vehicle moves into second gear.
BATTERY REPLACEMENT
34 •Open the bonnet by turning the 2 side fasteners and remove the screw on the grill.
35 •Unscrew and remove the battery fastener.
36 •Replace the battery. Replace the battery fastener.
37 •Connect the two plugs.
38 •Close the bonnet by turning the 2 side fasteners and tighten the screw.
BATTERY RECHARGE
39 •Disconnect the electrical system terminal A from the battery terminal B pressing with the fingers on the sides.
40 •Plug the battery charger terminal to a wall outlet following the instructions provided. Connect the terminal B and the battery charger
terminal C.
41 •Once the battery has been recharged, unplug the battery charger from the wall outlet, then disconnect terminals C and B.
42 •Connect terminal B and A till you hear the final click. Once recharging is complete, don't forget to close the simulated motor with the screw.
ASSEMBLY INSTRUCTIONS
INITIAL BATTERY CHARGE
!
• Remove battery and charger from packaging. Connect battery charger to a 120vac wall recepticle. Connect battery charger to battery.
