background image

ISSUED: 08-15-07  SHEET #: 055-9188-6   06-25-10 

Visit the Peerless Web Site at www.peerlessmounts.com

6 of 13

For customer care call 1-800-865-2112 or 708-865-8870.

Place projector mount assembly (

A

) on ceiling as a 

template and mark the center of the two mounting 
holes. Drill two 1/4" (6 mm) dia. holes to a minimum 
depth of 2.5" (64 mm). Attach projector mount 
assembly (

A

) using two concrete anchors (

G

), two 

fl at washers (

E

), and two #14 x 2.5" wood screws 

(

F

) as shown. 

NOTE: 

Mounting slots on projector mount assembly 

allow for 30° (±15°) of rotation before fully securing 
wood screw.

Tighten wood screws (

F

) using 3/8" (10 mm) socket 

wrench or phillips screwdriver until projector mount 
assembly (

A

) is fi rmly attached.

 

Skip to step 5.

F

Installation to Concrete Ceilings

A

E

G

FRONT OF 
MOUNT

•  Tighten wood screws fi rmly, but do not overtighten. 

Overtightening can damage the screws, greatly re-
ducing their holding power.

•  Never tighten in excess of 80 in • lb (9 N.M.).

WARNING

3

•  Always attach concrete anchors directly to load-

bearing concrete.

•  Never attach concrete anchors to concrete covered 

with plaster, drywall, or other fi nishing material. If 
mounting to concrete surfaces covered with a fi nish-
ing surface is unavoidable (not evaluated by UL), the 
fi nishing surface must be counterbored as shown be-
low. Be sure concrete anchors do not pull away from 
concrete when tightening screws. If plaster/drywall is 
thicker than 5/8", custom fasteners must be supplied 
by installer (not evaluated by UL).

WARNING

concrete 
surface

1

3

2

G

Drill holes and insert anchors (

G

).

Place plate (

A

) over anchors (

G

) and secure with screws (

F

).

Tighten all fasteners.

A

G

F

CUT

A

W

A

Y

 VIEW

INCORRECT

CORRECT

plaster/

dry wall

concrete

concrete

plaster/

dry wall

A

A

•  Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

•  Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

WARNING

Summary of Contents for PRS-1














Reviews: