background image

5 of 6

ISSUED: 06-04-10  SHEET #: 120-9085-1

Installation to Solid Concrete or Cinder Block

•  When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete 

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid 

part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica

-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to 

avoid breaking out the back of the hole when entering a void or cavity.

•  Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
•  Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard

-

ware and components.

WARNING

•  Always attach concrete anchors directly to load-

bearing concrete.

•  Never attach concrete anchors to concrete covered 

with plaster, drywall, or other finishing material. 

If mounting to concrete surfaces covered with 

a finishing surface is unavoidable, the finishing 

surface must be counterbored as shown below. 

Be sure concrete anchors do not pull away from 

concrete when tightening screws. If plaster/drywall 

is thicker than 5/8", custom fasteners must be 

supplied by installer.

WARNING

•  Tighten screws so that wall plate is firmly attached, 

but do not overtighten. Overtightening can damage 

screws, greatly reducing their holding power.

•  Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

F

A

C

solid concrete

cinder block

2

1

3

2

C

Drill holes and insert anchors (

C

).

Place plate (

A

) over anchors (

C

) and secure with screws (

F

).

Tighten all fasteners.

A

C

F

concrete 

surface

CUT

AW

AY

 VIEW

INCORRECT

CORRECT

wall 

plate

wall 

plate

plaster/

dry wall

plaster/

dry wall

concrete

concrete

Make sure that wall plate (

A

) is level, use it as a 

template to mark four mounting holes. Drill four 

5/16" (8 mm) dia. holes to a minimum depth of 2.5" 

(64 mm). Insert anchors (

C

) in holes flush with wall 

as shown (right). Place wall plate over anchors and 

secure with #14 x 2.5" screws (

F

). Level, then tighten 

all fasteners.

Summary of Contents for DS-VL-H036







Reviews: