background image

4 of 6

ISSUED: 06-04-10  SHEET #: 120-9085-1

Installation to Double Wood Stud Wall

•  Installer must verify that the supporting surface will safely support the combined load of the equipment and all 

attached hardware and components.

•  Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the 

screws, greatly reducing their holding power.

•  Never tighten in excess of 80 in. • lb (9 N.M.).
•  Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder 

is highly recommended.

•  Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install

-

ers are responsible to provide hardware for other types of mounting situations. 

WARNING

fig. 2.1

fig. 2.2

A

STUD

F

A

2

Wall plate (

A

) can be mounted to four studs that are 16" apart. Use a stud finder to locate the edges of the studs. 

Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each 

stud’s center. Place wall plate on wall as a template. Level plate, and mark the center of the four mounting holes. 

Make sure that the mounting holes are on the stud center lines. Drill four 5/32" (4 mm) dia. holes 2.5" (65 mm) 

deep. Make sure that the wall plate is level, secure it using four #14 x 2.5" wood screws (

F

) as shown in figure 2.2.

Summary of Contents for DS-VL-H036







Reviews: