Peco 23131504 Operator'S Manual Download Page 2

2

 PECO GRASS COLLECTION SYSTEM

TABLE OF CONTENTS

Safety

1.   

Read the operator’s manual carefully and familiarize yourself with the proper use of your attachment. Do not allow

       anyone who is not acquainted with the Safety Instructions to use your attachment.

2.   

Know the controls and how to stop quickly. READ THE OPERATOR’S MANUAL!

3.   

Do not allow children to operate the vehicle. Do not allow adults to operate it without proper instruction.

4.   

Be especially watchful of children and pets darting into the area while operating.

5.   

Keep your eyes and mind on your unit while mowing or operating your attachment. Don’t let others distract you.

6.   

Do not attempt to operate your unit or mower when not in the driver’s seat.

7.   

Always stop unit when emptying the container.

8.   

Stop unit, shut off deck attachment, set parking brake, shut off mower engine and remove spark plug wire before 

       removing clogs, removing or replacing hose, boot, blower cone, or performing any maintenance.

9.   

Mow across the face of slopes (not steeper than 10 degrees); never up and down the face of the slope.

10. 

It is recommended that the container be kept only half full when negotiating any slopes. Start mowing on slopes 

       when the container is empty.

11. 

Inspect your lawn and remove any foreign objects before mowing. Never deliberately run the mower across any 

       foreign object.

12. 

Wear ear protection if the noise level is offensive.

13. 

Wear eye protection to prevent debris from damaging your eyes.

SECTION                               PAGE

 

Safety  - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2

 

Safety Alert Symbols - - - - - - - - - - - - - - - - - - - - - - 3

 

Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4

I    INTRODUCTION AND DESCRIPTION - - - - - - - - - - - - 5
 

1-1 Introduction - - - - - - - - - - - - - - - - - - - - - - - - - 5

 

1-2 Description - - - - - - - - - - - - - - - - - - - - - - - - - 5

II   INSTALLATION FOR USE - - - - - - - - - - - - - - - - - - - - - 5
 

2-1 Preparation Of Mower - - - - - - - - - - - - - - - - - - 5

 

2-2 Left and Right Lower Frame Leg

 

      Assembly Installation - - - - - - - - - - - - - - - - - - 5-6

 

2-3 Lower Mount Assembly Installation - - - - - - - - - - 6

 

2-4 Rear brace Installation - - - - - - - - - - - - - - - - - - 6

 

2-5 Outer Engine Mount Tube Installation - - - - - - -  - 7

 

2-6 Engine Mount Arm Assembly Installation - - - - - - 7

 

2-7 Engine/Blower/Blade Assembly Installation- - - - - 7

 

2-8 Upper Frame Assembly Installation - - - - - - - - - - 8

 

2-9 Top Assembly To

 

      Upper Frame Assembly Installation - - - - - - - - - - 8

 

2-10 Hing Kit Installation - - - - - - - - - - - - - - - - - - - 9

 

2-11 Boot To Mower Deck Installation - - - - - - - - - - - 9

 

2-12 Blower Cone Installation - - - - - - - - - - - - - - - - 9

 

 SECTION                               PAGE

 

2-13 Front Weight Assembly Installation - - - - - - - - - 10

 

2-14 Length Of Hose Adjustment - - - - - - - - - - - - - - 11

 

2-15 Upper Hose Installation - - - - - - - - - - - - - - - - 11

 

2-16 Lower Hose To Blower Cone Installation- - - - - - 11

 

2-17 Lower Hose To Boot Installation - - - - - - - - - - - 11

 

2-18 Throttle Cable Installation - - - - - - - - - - - - - - - 12

 

2-19 Installation And Removal Of Collection Bags - - - 13

 

2-20 Impeller Blade Removal/Repalcement - - - - - - - 14

 

Exploded Views And Part Drawings - - - - - - - - - - 15-17

  III  OPERATING INSTRUCTIONS - - - - - - - - - - - - - - - - - 18
 

3-1 General Safety - - - - - - - - - - - - - - - - - - - - - - - 18

 

3-2 Operation & Tips On Mowing - - - - - - - - - - - - - - 18

 

3-3 Unloading the Collection System - - - - - - - - - - - 18

  IV  MAINTENANCE - - - - - - - - - - - - - - - - - - - - - - - - - - - 18
 

4-1 Maintenance Checklist - - - - - - - - - - - - - - - -  - - 18

 
  V   PARTS AND SERVICE - - - - - - - - - - - - - - - - - - - - - - 19
 

5-1 Parts And Service Information - - - - - - - - - - - - - 19

 

Safety Decals - - - - - - - - - - - - - - - - - - - - - - - - - - 20

 

Torque Specifications - - - - - - - - - - - - - - - - - - - - - 21

 

Drill Template  - - - - - - - - - - - - - - - - - - - - - - - - - - 22

 

Summary of Contents for 23131504

























Reviews: