background image

3

VSX

™ 

26e and VSX

 48e

Digital Loudspeaker Processors

The VSXe processors are  DSP-based, loudspeaker management systems that boast a 96kHz sample rate and a floating point DSP processor for 
quiet accurate filter response.  The crossover filters are fully adjustable and any input can be routed to any output.  The VSX® Editor Program for PC 
allows complete remote setup and operation via  the front panel USB port or by the rear panel Ethernet network connection.  Files can also be saved 
and loaded using this interface software.

This manual covers both the VSX 26e and VSX 48e DSP processors.  The units are essentially identical except for the number of inputs and outputs.  

Please read this guide carefully to ensure your personal safety as well as the safety of your equipment.

ENGLISH

Features

• 

Balanced Inputs:  VSX 26e 2, VSX 48e 4 

• 

Balanced Outputs: VSX 26e 6, VSX 48e 8

• 

96 kHz Sample rate

• 

24 bit Delta-Sigma A/D and D/A converters

• 

Dynamic range input to output greater than 109 dB (A-weighted) or 107 dB (unweighted)

• 

Every input features Gain, Mute, HP and LP filters, 8 bands of PEQ, polarity and Delay (680 mS),

• 

Every output features: 9 bands of PEQ, gain, compressor/limiter, polarity, Delay (680 mS), mute, and crossover/band-pass filters

• 

EQ filter types include: PEQ, Low-Shelf, Hi-Shelf, Low-Pass, High-Pass, All-Pass1 and All-Pass2.  

• 

Crossover/Band-pass filters feature Butterworth, Bessel or Linkwitz-Riley alignments from 1st order (6 dB/Oct) to 8th order (48 dB/Oct).

• 

Signal generator (sine, white noise, pink noise).

• 

Channels can be linked for simplified stereo operation.

• 

5 segment LED meters on each input 

• 

5 segment LED meters with limit indication on each output

• 

2 XLR balanced inputs and 6 XLR balanced outputs VSXe 26

• 

4 XLR balanced inputs and 8 XLR balanced outputs VSXe 48

• 

Maximum input and output level +20 dBu, XLR balanced inputs and outputs.

• 

Frequency response 20 Hz to 20 kHz +0, -1 dB

• 

THD+N < 0.01% at 1 kHz.

• 

Security lock

• 

USB B port for setup and control

• 

Ethernet port for setup and control.  

• 

Dimensions (HxWxD) 1.75" x 19" x 8"  / 45mm x 480mm x 20.5mm

• 

Weight 5.2 lbs /2.88 kg

• 

PC Editor Programs allow complete remote setup and operation via USB or Ethernet.

NOTE:

 The VSX processors can be setup and operated both from the front panel and from the VSX Editor running on a PC. The 

PC can be connected to the VSX via USB or Ethernet.

 

 

              

 

       

Summary of Contents for VSX 26e






















Reviews: