background image

PEAK® IOM57 Input/Output Modules Installation Instructions

20

Mounting

Screw mount on flat surface with three integral mounting clips on controller or horizontally 

mounted on single 35 mm DIN rail mount (preferred) inside a supplementary enclosure 

minimum IP20 rating that only qualified personnel can access.

Housing

Enclosure material: ABS and polycarbonate UL94 5VB; self extinguishing, Plenum-Rated
Protection Class: IP20 (IEC529)

Dimensions 

(Height x Width x Depth)

IOM5711: 

146 mm x 165 mm x 56 mm (5-3/4 in. x 6-1/2 in. x 2-1/4 in.) including terminals 

and mounting clips

IOM5731:

 146 mm x 190 mm x 61 mm (5-3/4 in. x 7-1/2 in. x 2-3/8 in.) including terminals 

and mounting clips

Note: 

Mounting space requires an additional 50 mm (2 in.) space on top, bottom and front 

face of controller for easy cover removal, ventilation and wire terminations.

Weight

0.5 kg (1.1 lb) maximum

Compliance

United States:

 UL Listed, File E107041, CCN PAZX, UL 916; FCC Compliant to CFR47, 

Part 15, Subpart B, Class A

Canada:

 UL Listed, File E107041, CCN PAZX7 CAN/CSA C22.2 No.205, Signal 

Equipment; Industry Canada Compliant, ICES-003

Europe:

 Johnson Controls declares that these products are in compliance with the 

essential requirements and other relevant provisions of the EMC Directive and Low Voltage 

Directive. Declared as Independently Mounted, Intended for Panel Mounting, Operating 

Control Type 1.B, 4kV rated impulse voltage, 100.7°C ball pressure test.

Australia and New Zealand: 

RCM Mark, Australia/NZ Emissions Compliant

The performance specifications are nominal and conform to acceptable industry standard. For application at conditions beyond 

these specifications, consult the local Johnson Controls® office. Johnson Controls shall not be liable for damages resulting from 

misapplication or misuse of its products.

European Single Point of Contact:

NA/SA Single Point of Contact:

APAC Single Point of Contact:

JOHNSON CONTROLS

WESTENDHOF 3

45143 ESSEN

GERMANY

JOHNSON CONTROLS

507 E MICHIGAN ST

MILWAUKEE WI 53202

USA

JOHNSON CONTROLS

C/O CONTROLS PRODUCT MANAGEMENT

NO. 22 BLOCK D NEW DISTRICT

WUXI JIANGSU PROVINCE 214142

CHINA

PEAK IOM57 Series technical specifications (Part 2 of 2 )

Summary of Contents for PEAK IOM57






















Reviews: