background image

Page 10

Technical Specification

Environment

Genius XE SCI 2

Minimum  Operating Ambient Temperature

5°C (41°F)

Maximum Operating Ambient Temperature

30°C (86°F)

Maximum Altitude

2000 m

Maximum Relative Humidity

80% Non-Condensing

Minimum Storage Temperature*

−20°C (−4°F)

Maximum Storage Temperature*

60°C (140°F)

*NOTE – Storage below 5°C (41°F) for long periods is not recommended. When taken out of storage the Generator 
should be allowed to acclimatize at room temperature for a minimum of 3 hours before operation. 

Generator Outlets

Curtain Maximum Flow^

Up to 26L/min @ 4.14bar  

(0.91cfm @ 60psi)

Source Maximum Flow^

Up to 32L/min @ 7.24bar  

(1.13cfm @ 105psi)

Exhaust Maximum Flow^

Up to 25L/min @ 4.83bar  

(0.88cfm @ 70psi)

Particles

<0.01µm

Phthalates

NONE

Suspended Liquids

NONE

Gas Outlets

1 × 5/16" (nitrogen) 2 × ¼” BSPP (air)

Drain Outlet

1 × ¼” BSPP

^

NOTE – These performance characteristics are valid only when paired with an SCIEX approved application. Refer to the 

appropriate application matrix for a list of supported products.

Electrical Requirements

Voltage

220 - 240v ±10%

Frequency

50/60 Hz

Current

9A

Input Connection

C20 Plug

Power Cord

C19 socket to local connection (10A minimum)

Pollution Degree

2

Installation / Over Voltage Category

II

General

Dimensions cm (inches) W × D × H

57 × 89.7 × 70 (22.4 × 35.3 × 27.6)

Generator Weight Kg (lbs)

103 Kg (227 lbs)

Shipping Weight Kg (lbs)

150 Kg (331 lbs)

Maximum Heat Output

5545 BTU/hr

Summary of Contents for Genius XE SCI 2






























Reviews: