background image

 

Page 

Fuze Part # 4532 - Patent Pending  

 May 2007 

May 2007 

Fuze Part # 4532 - Patent Pending 

Page

 

Page 

Fuze Part # 4532 - Patent Pending  

 May 2007 

May 2007 

Fuze Part # 4532 - Patent Pending 

Page

6. DO NOT operate the tilt-in-space if the trigger release levers and cables 

are not properly adjusted to ensure that the tilt-in-space is locked in place 
when engaged.

7. DO NOT TRAVERSE, CLIMB or GO DOWN ramps or slopes GREATER 

than 9°.

8. NEVER leave the occupied wheelchair unattended at any time, especially 

on an incline.

9. DO NOT attempt to reach objects if you have to move forward in the seat.

10. DO NOT attempt to reach objects if you have to pick them up from the 

ÀRRUE\UHDFKLQJGRZQEHWZHHQ\RXUNQHHV

11. DO NOT lean over the top of the back upholstery/seating system. This 

will change your center of gravity and may cause you to tip over.

12. DO NOT shift your weight or sitting position toward direction you are 

reaching as wheelchair may tip over.

13. WHEEL LOCKS ARE NOT BRAKES. DO NOT attempt to stop a mov-

ing wheelchair with the wheel locks.

14. DO NOT tip the wheelchair onto the rear wheels without assistance.

'2127XVHDQHVFDODWRUWRPRYHDZKHHOFKDLUEHWZHHQÀRRUV6HULRXV

bodily injury may occur.

16. Before attempting to transfer in or out of the wheelchair, every precaution 

should be taken to reduce the gap distance. Turn both casters parallel to 
the object you are transferring onto. When transferring to and from the 
wheelchair, ALWAYS ENGAGE BOTH WHEEL LOCKS.

17. If equipped with pneumatic tires DO NOT use wheelchair unless the tires 

KDYHWKHSURSHUWLUHSUHVVXUH'2127RYHULQÀDWHWKHWLUHV)DLOXUHWR

follow these suggestions may cause the tire to explode and cause bodily 
harm. Recommended tire pressure is listed on the side wall of the tire.

18. DO NOT use ANY parts, accessories, or adapters other than those 

authorized by PDG. Otherwise, the warranty is void.

19. DO NOT attempt to lift a wheelchair by lifting on any removable (detach-

able) parts. Lifting by means of any removable (detachable) parts of a 
wheelchair may result in injury to the user or damage to the wheelchair.

20. DO NOT use the folding links or spreader bar for lifting or transporting 

the wheelchair.

21. DO NOT use the folding links spreader bar as a weight bearing support.

22. DO NOT stand on the frame of the wheelchair. PDG recommends that 

anti-tippers BE attached at all times.

9

Summary of Contents for FuzeT20



































Reviews: