PCS DTC6 Installation And Operating Instructions Manual Download Page 7

 

Option 

Factory Default 

Possibilities 

ON

 Pushbutton 

UPB Transmissions 

Button Mode =  

On Button 

Link = 001 

Configure any of 15 different UPB Messages 
to be transmitted upon each of four 
Pushbutton Events to any of 254 Link IDs. 

OFF

 Pushbutton 

UPB Transmissions 

Button Mode =  

Off Button 

Link = 002 

Configure any of 15 different UPB Messages 
to be transmitted upon each of four 
Pushbutton Events to any of 254 Link IDs. 

A

B

C

, and 

D

 

Pushbutton UPB 
Transmissions 

Button Mode =  

Scene Activator 

Links = 003, 004, 005, 

006 

Configure any of 15 different UPB Messages 
to be transmitted upon each of four 
Pushbutton Events to any of 254 Link IDs. 

UP

 Pushbutton UPB 

Transmissions 

Button Mode =  

Bright Button 

Link = Use Last Link 

Configure any of 15 different UPB Messages 
to be transmitted upon each of four 
Pushbutton Events to any of 254 Link IDs. 

DOWN

 Pushbutton 

UPB Transmissions 

Button Mode =  

Dim Button 

Link = Use Last Link 

Configure any of 15 different UPB Messages 
to be transmitted upon each of four 
Pushbutton Events to any of 254 Link IDs. 

ON

OFF

A

B

C

and 

D

 LED Indicator 

Receiving Link ID 

Each LED Indicator is 

assigned to its 

pushbutton’s Link ID. 

Each LED Indicator can be assigned to any 
of 254 Link IDs. 

ON

OFF

A

B

C

and 

D

 LED Indicator 

Mutual Exclusivity 

Each LED Indicator is 

mutually exclusive (one 

LED on at a time). 

Each LED Indicator can be configured as 
mutually exclusive (one LED on at a time) or 
independent (multiple LEDs on at one time). 

UPB Transmission 
Attempts 

1, 2, 3, or 4 transmissions per event. 

UPB ID 

NID = 255,  

UID = 003 

Many UPB Identification parameters can be 
configured including the Network ID (NID), 
Unit ID (UID), Network Password, Network 
Name, Room Name, Device Name, etc. 

LED Brightness  

High 

High, Medium, Low, Faint, None 

LED Backlighting 
(very low lighting of 
all buttons so device 
can be located in 
darkness) 

Enabled Enabled 

or 

Disabled 

Table 1: 6-Button Controller Configuration Options 

Page 6 of 8 

Summary of Contents for DTC6










Reviews: