Pco pco.edge 4.2 bi User Manual Download Page 2

 

 

 
 
 

PCO asks you to carefully read this manual before using the 
pco.edge camera system and follow the instructions.  
 
In case of any questions or comments, contact us at PCO. 

 

 

telephone  

 

+49 (0) 9441 2005 50  

fax    

 

+49 (0) 9441 2005 20 

email   

 

[email protected]  

postal address   

PCO AG 

 

 

 

Donaupark 11 

 

 

 

93309 Kelheim, Germany 

 
 
 
 

The cover photo shows an exemplary PCO camera system.  
The lens is sold separately. 

 
 

 

Copyright © 2019  PCO AG (called PCO in the following text), Kelheim, 

Germany. All rights reserved. PCO assumes no responsibility for errors or 
omissions in these materials. These materials are provided as is without 

warranty of any kind, either expressed or implied, including but not limited to, 

the implied warranties of merchantability, fitness for a particular purpose, or 
non-infringement. PCO further does not warrant the accuracy or 

 

completeness of the information, text, graphics, links or other items 
contained within these materials. PCO shall not be liable for any special, 

indirect, incidental, or consequential damages, including without limitation, 
lost revenues or lost profits, which may result from the use of these materials. 

The information is subject to change without notice and does not represent a 
commitment on the part of PCO in the future. PCO hereby authorizes you to 

copy documents for non – commercial use within your organization only. In 
consideration of this authorization, you agree that any copy of these 

documents, which you make, shall retain all copyright and other proprietary 

notices contained herein. Each individual document published by PCO may 
contain other proprietary notices and copyright information relating to that 

individual document. Nothing contained herein shall  be construed as 
conferring by implication or otherwise any license or right under any patent or 

trademark of PCO or any third party. Except as expressly provided, above 
nothing contained herein shall be construed as conferring any license or right 

under any PCO copyright. Note that any product, process, or technology in 
this document may be the subject of other intellectual property rights 

reserved by PCO, and may not be licensed hereunder. 

 

 

Released: July 2019 © PCO AG 

 

 

pco.edge 4.2 bi (UV) user manual V1.00  © PCO AG, Germany 

       

 

Summary of Contents for pco.edge 4.2 bi



































Reviews: