background image

www.modellmarkt24.ch;   www.modellmarkt24.de

PINO 3.0 Building Instruction                                                                

August 2018 

                                                                                                                        

www.pcm.at                                                                                                                                                            

Prepare the parts for gluing 
the control levers into the 
wing. 

Grind all gluing 

surfaces

, the slot of the 

control surfaces and the 
levers themselves. 
 

 

 

The 

bolt

 of the 

lever 

connector

 has sharp edges 

that are bigger than the bolt 
diameter. You should 

remove these edges

, before 

you put the connector into 
the lever. It is easy to clean 
that bolt with nose pliers. 
Grab the bolt with the nose 
pliers and move the 
connector up and down 
about 3 times as shown in 
the picture. Repeat this that 
often until the connector is 
able to 

move in the lever 

hole without a lot of 
friction

 

 

 

Before you glue the lever into the control surface, 

fix the 

connector

 

to the lever

 
The short lever is for the aileron and the long lever for the flaps. 

 

 

You can use 

runny super glue

 to fix the levers. This kind of 

bonding will be strong enough for the forces occurring. 

 

 

 

 

www.modellmarkt24.ch;   www.modellmarkt24.de

Summary of Contents for PINO 3.0















Reviews: