background image

 

 

Safety Warning 

 

Caution:

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT 

TYPE.DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS 

 

FCC Warning: 
This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B  digital device,  pursuant  to  part  15  of  the F CC  Rules.  These limits  are 
designed  to provide  reasonable  protection  against  harmful interference in  a  residential installation.  This  equipment  generates,  uses  and  can  radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there 
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, 
which  can  be  determined  by  turning  the  equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct  the  interference  by  one  or  more  of  the  following 
measures: 
• Reorient or relocate the receiving antenna. 
• Increase the separation between the equipment and receiver. 
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
• Consult the dealer or an experienced radio/TV technician for help. 
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. 
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, 
and (2) this device must accept any interference received, including interference that may cause undesired operation. 
 

 

Specific Absorption Rate (SAR) information: 
This equipment meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by 
independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin 
designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.199 
W/kg averaged over one gram of tissue. Device types: equipment (FCC ID:

 

2ALJJJ601) has also been tested against this SAR limit. This device was tested 

for typical body-worn operations with the back of the equipment kept 10mm from the body. To maintain compliance with FCC RF exposure requirements, use 
accessories that maintain a 10mm separation distance between the user's body and the back of the equipment. The use of belt clips, holsters and similar 
accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC 
RF exposure requirements, and should be avoided. 

 

This device is restricted to indoor use where operated in the European and USA.Canada Community using frequency in 5150MHz ~ 5250MHz to reduce the 

potential for interference. 

Summary of Contents for J601






























Reviews: