PCchips M938 Series User Manual Download

Page: 8 / 39

♦

Meet All Applicable IEEE802.3, 10Base-T and 100Base-
TX Standards

Onboard I/O Ports

The mainboard has a full set of I/O ports and connectors:

♦

Two PS/2 ports for mouse and keyboard

♦

One serial port

♦

One parallel port

♦

One VGA port

♦

Four back-panel USB2.0 ports and extra two USB2.0 ports
(onboard USB header JUSB1)

♦

Audio jacks for microphone, line-in and line-out

Hardware Monitoring

♦

Built-in hardware monitoring for CPU & System
temperatures, fan speeds and mainboard voltages.

Onboard Flash ROM

♦

Supports Plug and Play configuration of peripheral devices
and expansion cards

USB 2.0

♦

Compliant with Universal Serial Bus Specification
Revision 2.0

♦

Compliant with Intel’s Enhanced Host Controller
Interface Specification Revision 0.95

♦

Compliant with Universal Host Controller Interface
Specification Revision 1.1

♦

PCI multi-function device consists of two

UHCI Host

Controller

cores for full-/low-speed signaling and one

EHCI Host Controller

core for high-speed signaling

♦

Root hub consists 4 downstream facing ports with
integrated physical layer transceivers shared by

UHCI

and

EHCI

Host Controller

♦

Support PCI-Bus Power Management Interface
Specification release 1.1

♦

Legacy support for all downstream facing ports

Summary of Contents for M938 Series








































Search results

Summary of Contents for M938 Series

Reviews:

Related manuals for M938 Series

Brands by name

Popular brands

PCchips M938 Series, User Manual

Search results

Summary of Contents for M938 Series

Reviews:

Related manuals for M938 Series

Brands by name

Popular brands