PCchips M925 Series User Manual Download Page 41

Page: 41 / 49

3: BIOS Setup Utility

port.

Parallel Port
DMA

Use this item to assign a DMA channel to
the parallel port.

OnBoard
Game Port

This item enables or disables the I/O
address for the game port.

OnBoard MIDI
Port

Use this item to enable or disable the
onboard MIDI port, and to assign a port
address.

MIDI Port IRQ

Use this item to assign IRQ 7 to the
parallel port.

OnBoard IDE

Use this item to enable or disable the
onboard IDE channel.

Audio Device

This item enables or disables the AC’97
audio chip.

Modem Device

This item enables or disables the MC’97
modem chip.

Ethernet
Device

This item enables or disables the onboard
Ethernet LAN.

USB
Controller

Use this item to select the USB ports or
disabled.

USB Device
Legacy
Support

This item allows you to enable the USB
device, if you have installed a USB device
on the system board.

ThumbDrive
Support For
DOS

Enable this item to make a small portion of
memory storage device for the USB ports.

Summary of Contents for M925 Series


















































Search results

Summary of Contents for M925 Series

Reviews:

Related manuals for M925 Series

Brands by name

Popular brands

PCchips M925 Series, User Manual

Search results

Summary of Contents for M925 Series

Reviews:

Related manuals for M925 Series

Brands by name

Popular brands