background image

 

 

Figure 18. 

DC Bias Voltage Measurement 

 
10.0 REPAIR/RETURN PROCEDURE 

Because  of  the  nature  of  most  IMI 
instrumentation,  field  repair  is  typically  NOT 
recommended  and  may  void  any  warranty.    If 
factory  service  is  required,  contact  IMI  for  a 

RETURN  MATERIAL  AUTHORIZATION  (RMA)

 

number  prior  to  sending  equipment  to  the 
factory.  Please have information available, such 
as  model  and  serial  number.    Also,  to  insure 
efficient  service,  be  sure  to  include  a  written 
description of the symptoms and problems with 
the equipment to a local sales representative or 
distributor, or contact IMI if none are located in 
your area. 
 
Customers outside the U.S. should consult their 
local  IMI  distributor  for  information  on 
returning  equipment.    For  exceptions,  please 
contact  the  International  Sales  department  at 
IMI  to  request  shipping  instructions  and  an 

RMA.    For  assistance,  please  call 

(716)  684-

0003

, or fax us at 

(716) 684-3823

.  You may also 

receive assistance via e-mail at 

[email protected]

 or 

visit our website at 

www.pcb.com. 

 

11.0 CUSTOMER SERVICE/WARRANTY 
 

IMI, a division of PCB Piezotronics, guarantees 

Total 

Customer Satisfaction

.  If, at any time, for any 

reason, you are not completely satisfied with any IMI 
product, IMI will repair, replace or exchange it at no 
charge.  You may also choose to have your purchase 
price refunded. 
 
IMI instrumentation is warranted against defective 
material workmanship for 1 year unless otherwise 
expressly specified.  Damage to instruments caused 
by incorrect power or misapplication, is not covered 
by warranty.  

If there are any questions regarding 

power, intended application, or general usage, 
please consult with your local sales contact or 
distributor.  

Batteries or expendable hardware items 

are not covered by warranty. 
 
IMI offers to all customers, at no charge, 24-hour 
phone support.  This service makes product or 
application support available to our customers, day 
or night, seven days a week.  When unforeseen 
problems or emergency situations arise, call the 

IMI 

Hot Line at (716) 684-0003

, and an application 

specialist will assist you. 

 

 

Summary of Contents for CS625B11




















Reviews: