PCB Piezotronics 301A11, Installation And Operating Manual

Page: 45 / 77

Model Number
394A 11
CALIBRATION SYSTEM
Revision: H
ECN #: 50036
P erfo rm an ce EN G L ISH SI
Sensitivity(± 0.5 %)(Voltage) 100 mV/g 10.2 mV/(m/s²) [1]
Measurement Range(± 5V)(Output) 50 ±g pk 490 ±m/s² pk
Frequency Range(± 2 %) 5 to 5,000 Hz 5 to 5,000 Hz
Frequency Range (± 5 %) 0.5 to 10,000 Hz 0.5 to 10,000 Hz
Frequency Range (± 10 %) 0.3 to 14,000 Hz 0.3 to 14,000 Hz
Resonant Frequency(Mounted) ≥ 35 kHz ≥ 35 kHz
Broadband Resolution(1 Hz to 10 kHz) 0.004 g rms 0.039 m/s² rms [2]
Amplitude Linearity ≤ 1 % ≤ 1 % [3]
Transverse Sensitivity ≤ 3 % ≤ 3 %
Sensitivity(Base Strain) 0.0001 g/µε 0.001 (m/s²)/µε
En viro n m en tal
Warm Up < 12.0 sec < 12.0 sec
Temperature Range(Operating) -65 to +250 °F -54 to +121 °C
Electrical
Spectral Noise(1 Hz) 235 (µm/s²)/√Hz 2,303 [2]
Spectral Noise (10 Hz) 55 (µm/s²)/√Hz 539 [2]
Spectral Noise (100 Hz) 18 (µm/s²)/√Hz 176 [2]
Spectral Noise (1 kHz) 12 (µm/s²)/√Hz 118 [2]
P h ysical
Sensing Element Quartz/Shear Quartz/Shear
Housing Material Stainless Steel/Welded Stainless Steel/Welded
Size (Hex x Height x Height x Width x Depth)1.19 in x 1.5 in x 6.3 in x 2.4 in x
11.0 in
30.2 mm x 38.1 mm x 16 cm x
6.1 cm x 28 cm
Weight 6.2 oz 176 gm [2]
Electrical Connector 10-32 Coaxial/Side 10-32 Coaxial/Side
Mounting Thread(Standard) 1/4-28 UNF 1/4-28 UNF
Mounting Thread (Unit Under Test) 10-32 UNF 10-32 UNF
Mounting Torque 20 to 30 in-lb 225 to 338 N-cm
Power(± 5%)(Required) 36 VDC 36 VDC [4]
Weight 1.51 lb 685 gm [2]
Cable Connector(Input) BNC Jack/Rear BNC Jack/Rear
Cable Connector (Output) BNC Jack/Rear BNC Jack/Rear
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
M - Metric Mount
[5]
Sensitivity± 0.5 10 mV/(m/s²) 98 mV/g
OP TION A L VERSION S
Optional versions have identical specifications and accessories as listed for the standard model except
where noted below. More than one option may be used.
N OTES:
[1]All sensor specifications are valid only when used with matched power supply.
[2]Typical.
[3]Zero-based, least-squares, straight line method.
[4]Provided by 488A04.
[5]Measured at 159 Hz.
Date: 10/18/2019 Date: 10/18/2019 Date: 10/18/2019 Date: 10/18/2019 11307
Entered: LK Engineer: CPH Sales: WDC Approved: DY Spec Number:
3425 Walden Avenue, Depew, NY 14043
Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: info@pcb.com
SU P P L IED A C C ESSORIES:
Model 003C10 Low-noise, blue, coaxial, PTFE cable, 10-ft, 10-32 coaxial plug to BNC plug (1)
Model 003D03 Low-noise, blue, coaxial, PTFE cable, 3-ft, BNC plug to BNC plug (1)
Model 017AXX Power Cord (1)
Model 080A149 Calibration adaptor, 10-32 to 5-40 (for Model 394A11 calibration standard) (1)
Model 081A08 Mounting Stud (10-32 to 1/4-28) (2)
Model 081A90 Mounting stud, 10-32 to 5-40 (2)
Model 081B05 Mounting Stud (10-32 to 10-32) (2)
Model 081B20 Mounting Stud, with shoulder (1/4-28 to 1/4-28) (2)
Model 301A11 Calibration ICP® accel., 100 mV/g, 50g, 0.5 to 10 kHz, 10-32 side conn., 1/4-28 thd
on bottom, 10-32 thd on top (1)
Model 482A23 1-channel, line-powered, ICP® sensor signal cond., BNC input/output conn. X0.9 to
x1.1 gain, (for use in 394A10/394A11 systems) (1)
Model 488B04 Power Supply, 100 to 125 VAC or 200 to 250 VAC input, 27 VDC @ 20 mA output. (1)
Model ACS-1 NIST traceable frequency response (10 Hz to upper 5% point).
Model ACS-10/ACS-4 NIST Tracable frequency sweep (0.5 Hz to upper 5% point) (1)
Model ACS-4 Single axis, low frequency phase and amplitude response cal (from 0.5 to 10Hz)
Model M080A149 Mounting adaptor (10-32 to M3 x 0.50) (1)
Model M081B05 Mounting Stud 10-32 to M6 X 0.75 (2)
Model M081B20 Mounting Stud 1/4-28 to M6 X 0.75 (2)