PCB Piezotronics 1630-04C Installation And Operating Manual Download Page 9

 

Model Number

 

1630-04C

 

STRAIN GAGE LOAD CELL

 

Revision: C 

ECN #: 41486

 

 

Performance 

ENGLISH 

SI 

Measurement Range

 

100 lb

 

445 N

 

[5]

 

Sensitivity(± 10 %)

 

2 mV/V

 

2 mV/V

 

[6]

 

Non-Linearity

 

 0.05 % FS

 

 0.05 % FS

 

 

Hysteresis

 

 0.03 % FS

 

 0.03 % FS

 

 

Non-Repeatability

 

 0.02 %RO

 

 0.02 %RO

 

 

Resonant Frequency

 

1.8 kHz

 

1.8 kHz

 

 

Creep(in 20 minutes)

 

 0.08 %

 

 0.08 %

 

 

Environmental 

Overload Limit

 

150 lb

 

667 N

 

 

Load Limit(Side Force, F

X

 or F

Y

)

 

10 lb

 

44.5 N

 

[3]

 

Load Limit

(Bending Moment, M

X

 or M

Y

)

 

20 in-lb

 

2.26 Nm

 

[3]

 

Load Limit

(Axial Torque, M

Z

)

 

20 in-lb

 

2.26 Nm

 

[3]

 

Temperature Range(Operating)

 

0 to +200 °F

 

-18 to +93 °C

 

 

Temperature Range

(Compensated)

 

+70 to +170 °F

 

+21 to +77 °C

 

 

Temperature Effect on Output(Maximum)

 

± 0.0008 %Reading/°F

 

± 0.0015 %Reading/°C

 

[4]

 

Temperature Effect on Zero Balance(Maximum)

 

± 0.0015 %FS/°F

 

± 0.027 %FS/°C

 

[4]

 

Electrical 

Bridge Resistance

 

350 Ohm

 

350 Ohm

 

[1]

 

Excitation Voltage(Recommended)

 

10 VDC

 

10 VDC

 

[2]

 

Insulation Resistance

 

>5x10

9

 Ohm

 

>5x10

9

 Ohm

 

 

Zero Balance

 

± 1 % FS

 

± 1 % FS

 

 

Physical 

Size (Length x Height x Width)

 

2.00 in x 2.50 in x 0.625 in

 

51 mm x 64 mm x 16 mm

 

 

Weight

 

0.23 lb

 

104 g

 

 

Mounting Thread

 

1/4-28 thread

 

No Metric Equivalent

 

 

Housing Material

 

Aluminum

 

Aluminum

 

 

Sensing Element

 

Strain Gage

 

Strain Gage

 

 

Deflection at Full Scale Capacity

 

0.002 in

 

0.05 mm

 

 

Electrical Connector

 

10 ft - Integrated Cable

 

10 ft - Integrated Cable

 

 

Electrical Connection Position

 

Side

 

Side

 

 

All specifications are at room temperature unless otherwise specified. 
In the interest of constant product improvement, we reserve the right to change specifications without notice. 

ICP

®

 is a registered trademark of PCB Group, Inc. 

 

OPTIONAL VERSIONS 

Optional versions have identical specifications and accessories as listed for the standard model 

except where noted below. More than one option may be used.

 

 
 
 
 

 

 

NOTES:

[1] Nominal.
[2] Calibrated at 10 VDC, usable 5 to 20 VDC or VAC RMS.
[3] Singularly applied, i.e. no other extraneous loads.
[4] Over compensated operating temperature range.
[5] FS - Full Scale.
[6] RO - Rated Output.

 

Entered: AP

 

Engineer: JSD

 

Sales: KWW

 

Approved: DA

 

Spec Number:

 

Date: 6/12/2013

 

Date: 6/12/2013

 

Date: 6/12/2013

 

Date: 6/12/2013

 

45995 

 

PCB Load & Torque, Inc. 
24350 Indoplex Circle 
Farmington Hills, MI 48335 
UNITED STATES 
Phone: 866-684-7107 
Fax: 716-684-0987 
E-Mail: [email protected] 
Web site: http://www.pcbloadtorque.com 

Summary of Contents for 1630-04C











Reviews: