Model Number
1220-12ADB
LOW PROFILE LOAD CELL, DUAL BRIDGE
Revision: NR
ECN #: 42816
Performance
ENGLISH
SI
Measurement Range(100 x 10^6 cycles)
50 klb
223 kN
[7][8]
Sensitivity(± 10 %)
4.0 mV/V
4.0 mV/V
[9][1]
Non-Linearity
≤
0.05 % FS
≤
0.05 % FS
Hysteresis
≤
0.05 % FS
≤
0.05 % FS
Non-Repeatability
≤
0.02 %RO
≤
0.02 %RO
Eccentric Load Sensitivity
0.1 %/in
0.1 %/25.4mm
Resonant Frequency
15 kHz
15 kHz
Side Load Sensitivity
0.1 %/in
0.1 %/25.4mm
Creep(in 20 minutes)
0.025 %
0.025 %
Static Error Band
≤
0.05 % FS
≤
0.05 % FS
[7]
Environmental
Overload Limit
75 klb
334 kN
Load Limit(Side Force, F
X
or F
Y
)
25 klb
111 kN
[3]
Load Limit
(Bending Moment, M
X
or M
Y
)
25k in-lb
2825 Nm
[3]
Load Limit
(Axial Torque, M
Z
)
25k in-lb
2825 Nm
[3]
Temperature Range(Operating)
-65 to +200 °F
-54 to +93 °C
Temperature Range
(Compensated)
+15 to +115 °F
-9 to +46 °C
Temperature Effect on Output(Maximum)
± 0.0008 %Reading/°F
± 0.0018 %Reading/°C
[4]
Temperature Effect on Zero Balance(Maximum)
± 0.0008 %FS/°F
± 0.0018 %FS/°C
[4]
Moisture Protection
See note
See note
[5]
Rust Resistance
See note
See note
[6]
Electrical
Bridge Resistance
350 Ohm
350 Ohm
[1]
Excitation Voltage(Recommended)
10 VDC
10 VDC
[2]
Insulation Resistance
>5k GOhm
>5k GOhm
Zero Balance
≤
1 %RO
≤
1 %RO
Physical
Size (Diameter x Height)
6.06 in x 3.50 in
153.90 mm x 88.90 mm
[10]
Weight
21 lb
9.53 kg
Mounting Thread
1 1/4 - 12 UNF-3B
No Metric Equivalent
Sensing Element
Strain Gage
Strain Gage
Mounting Torque
1400 in-lb
158 Nm
Deflection at Full Scale Capacity
0.001 in
0.03 mm
Electrical Connector
PT02E-10-6P (2)
PT02E-10-6P (2)
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
ICP
®
is a registered trademark of PCB Group, Inc.
OPTIONAL VERSIONS
Optional versions have identical specifications and accessories as listed for the standard model
except where noted below. More than one option may be used.
NOTES:
[1]
Nominal.
[2]
Calibrated at 10 VDC, usable 5 to 20 VDC or VAC RMS.
[3]
Singularly applied, i.e. no other extraneous loads.
[4]
Over compensated operating temperature range.
[5]
Gages, resistors and wiring coated against moisture, double diaphragms top and bottom,
rubber gaskets under connectors.
[6]
All none load surfaces painted, load surfaces and mounting thread coated with dry film rust
inhibitor.
[7]
FS - Full Scale.
[8]
Calibrated in tension and compression.
[9]
RO - Rated Output.
[10] See Outline Drawing 58695 for Complete Dimensions.
OPTIONAL ACCESSORIES:
Model 084A56 Pre-Tension Stud
Model 084A90 Connector Shroud (2)
Model 181-012A PT06A-10-6S(SR)
Model 8311-01-10A CABLE
Entered: AP
Engineer: PE
Sales: KWW
Approved: JSD
Spec Number:
Date: 5/6/2014
Date: 5/6/2014
Date: 5/6/2014
Date: 5/6/2014
58694
PCB Load & Torque, Inc.
24350 Indoplex Circle
Farmington Hills, MI 48335
UNITED STATES
Phone: 866-684-7107
Fax: 716-684-0987
E-Mail: [email protected]
Web site: http://www.pcbloadtorque.com
