background image

7

UNIT DAMAGE HAZARD

Failure to follow this caution may result in furnace

component damage.
Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and hazardous

operation.

CAUTION

!

3. Disconnect wires or connectors to flame rollout switch, gas

valve, igniter, and flame sensor.

4. Disconnect combustion--air intake pipe from intake hous-

ing.

5. Remove the pressure switch tube from intake housing.
6. Remove screws attaching intake housing to burner box, and

rotate intake housing away from burner box for removal.

7. Using backup wrench, disconnect gas supply pipe from fur-

nace gas control valve.

8. Disconnect pressure tubing from gas valve.
9. Remove two screws attaching top filler panel and rotate up-

wards to gain access to screws attaching burner box to cell

panel.

10. Remove screws attaching burner box to cell panel. (See Fig.

6.)

NOTE

: Burner box, cover, manifold, gas valve, and burner

assembly should be removed as one assembly.

11. Clean heat exchanger openings with a vacuum and a soft

brush. (See Fig. 8.)

NOTE

: After cleaning, inspect the heat exchangers to ensure they

are free of all foreign objects that may restrict flow of combustion
products.

PRIMARY HX

INLET OPENINGS

A96305

Fig. 8 -- Cleaning Inlet Openings of Primary

Heat Exchangers

UNIT MAY NOT OPERATE

Failure to follow this caution may result in improper or

intermittent unit operation.
The ground wire from the gas valve MUST be attached to

the burner box attachment screw.

CAUTION

!

12. Reverse items 3 through 10 for reassembly.

NOTE

: Be sure burner box gasket is installed between burner box

and cell panel. (See Fig. 6.) If gasket is damaged, replace it.

NOTE

: Inspect combustion--air intake housing. If foamed gasket

was removed, check for any damage. If gasket is damaged in any
way, it must be repaired. To repair, remove damaged gasket
section, apply sealant releasing agent such as PAM cooking spray
or equivalent (must not contain corn nor canola oil, halogenated
hydrocarbons nor aromatic content, to prevent inadequate seal
from occurring) to burner box and apply a small bead of G.E. RTV
162, G.E. RTV 6702, or Dow--Corning RTV 738 sealant to edge
of combustion--air intake housing. (See Fig. 9.)

PAM

RTV

A93087

Fig. 9 -- Combustion--Air Intake Housing

Gasket Repair

13. Refer to furnace wiring diagram and reconnect wires to

flame rollout switch, gas valve, igniter, and flame sensor.

14. Reconnect pressure switch tubes to gas valve and intake

housing. Refer to tube routing label on main furnace door
for proper tube location. (See Fig. 10.) Be sure tubes are not
kinked.

15. Turn on gas and electrical supplies to furnace.
16. Check furnace operation through two complete heat operat-

ing cycles. Look through sight glass in burner enclosure to
check burners. Burner flames should be clear blue, almost

transparent. (See Fig. 11.)

17. Check for gas leaks.

FIRE OR EXPLOSION HAZARD

Failure to follow this warning could result in personal

injury, death or property damage.
Never test for gas leaks with an open flame. Use a

commercially available soap solution made specifically

for the detection of leaks to check all connections.

!

WARNING

18. Replace main furnace door.

Secondary Heat Exchangers

NOTE

:

The condensing side (inside) of the secondary heat

exchangers CANNOT be serviced or inspected. A small number of
bottom outlet openings can be inspected by removing the inducer
assembly. See Flushing Collector Box and Drainage System
section for details on removing inducer assembly.

Step 5 — Flushing Collector Box and Drainage

System

1. Turn off gas and electrical supplies to furnace.
2. Remove main furnace door.
3. Disconnect inducer motor and pressure switch wires or con-

nectors.

PG

9M

AB

Summary of Contents for PG9MAB



















Reviews: