PAU Edge 540T Instruction Manual Download Page 1

Property of Performance Aircraft Unlimited 

Property of performance Aircraft Unlimited 

1

 
 
 
 
 

50/60cc Edge 540T 

Instruction Manual 

 

Congratulations and thank you for purchasing the Performance Aircraft Unlimited 50/60cc Edge 540. The 
Zivko Edge 540 was designed and developed to be the best aerobatic aircraft in the world and it delivered! Not 
only does this aircraft dominate IAC competition but has also found a home in the Red Bull racing circuit where 
it has won title after title. The 540 stands for the powerful Lycoming 540 motor that puts out more than 300hp. 
Made from modern composites, this aircraft is sure to be on the podium for some time to come. 
 
The PAU Edge is no different! Designed with 1474 sq inches of wing area while keeping the total weight down 
has made this aircraft a true performer. All wood construction and top quality hardware make it hard to beat. If 
you want an aircraft precise enough to compete in IMAC or to turn it loose for the wildest 3D maneuvers on the 
planet, the PAU Edge’s are the only choice. PAU has also increased the aileron size and really beefed up 
the wings. The fuse is redesigned and has a much more aggressive stance. More side area and stubble surface 
changes clean this aircraft up further in knife. Just as it’s full-scale counterpart, the PAU Edge has found victory 
in competition aerobatics. 
 
 

Summary of Contents for Edge 540T






















Reviews: