background image

 

3

Thank you and congratulations on the purchase of your new Model 

330PUB Patty Molding Machine from Patty-O-Matic, Inc!  The Model 330PUB 
will form, interleave paper between, and perfectly stack patties.  This machine is 
designed for easy operation and cleaning.  Please become familiar with this 
manual and your machine will give you many years of productive service. 

The Model 330PUB is shipped to you in three cartons which contain the 

patty machine, feed tray, mold plate guard, spare parts box, receiving table, mobile 
table, and this manual.  If you purchased your machine with any other accessories, 
such as a mobile table or patty paper, these items may be in a separate carton.  The 
parts box that comes with the machine should include a bottle of machine 
lubricant, a speed driver, samples of patty paper, and a spare parts kit.  

Your machine is equipped with two interlocks.  One is located on the front 

of the machine and one is located on the top of the machine.  The Mold Plate 
Guard must be installed on the machine to engage the interlock on the front of the 
machine and the Feed Tray including the Guard must be installed on top of the 
Hopper to engage the interlock on top of the machine. 

     

  

 

 
 
 
 
 
 
 

Mold Plate 

Guard 

Mold Plate 

Guard Knobs 

Round Key Latch 

Interlock 

Installing the Mold Plate Guard 

Loosen Guard Knobs on the Hopper and 
place Mold Plate Guard under the fender 
washers located under the knobs.  
Tighten down on Guard Knobs.  To 
Activate the interlock switch, slide push 
rod against the plunger, inside the key 
latch, and turn rod to the right.  This will 
lock the push rod in place and activate 
your interlock switch.   

Installing the Feed Tray 

Place stainless steel tube of feed tray over 
the Hopper.  Make Sure the Switch Plunger 
on the bottom of Feed Tray depresses the 
Tower Stem inside the Tower Sleeve on 
the top of the machine.  

   

Safety Interlock 

Tower 

Hopper 

Push Rod 
and Collar 

Feed Tray 

Stainless 

Steel Tube 

DO NOT ATTEMPT TO RUN THIS 

MACHINE WITHOUT THE FEED 

TRAY AND THE MOLD PLATE 

GUARD IN THEIR PLACE!!  

FAILURE TO DO SO COULD 

RESULT IN SERIOUS BODILY 

INJURIES!!     

Switch Plunger Located 

on back of Tray 

Summary of Contents for 330PUB






























Reviews: