background image

45

APPENDIX B

PATTON NETLINK-E1™ MODEL 2701RC

CABLE RECOMMENDATIONS

The Patton NetLink E1™ Series has been performance tested by

Patton technicians using twisted-pair cable with the following charac-
teristics:

Wire Gauge

Capacitance

Resistance

19 AWG

83nf/mi or 15.72 pf/ft.

.0163 Ohms/ft.

22 AWG

83nf/mi or 15.72 pf/ft.

.0326 Ohms/ft.

24 AWG

83nf/mi or 15.72 pf/ft.

.05165 Ohms/ft.

To gain optimum performance from the Model 2701RC Series,

please keep the following guidelines in mind:

• 

Always use twisted pair wire—this is not an option.

• Use twisted pair wire with a capacitance of 20pf/ft or less.

• Avoid twisted pair wire thinner than 26 AWG (i.e. avoid AWG
numbers higher than 26)

• Use of twisted pair with a resistance greater than the above
specifications may cause a reduction in maximum distance obtain-
able.  Functionality should not be affected.

• Many environmental factors can affect the maximum distance
obtainable at a particular site. 

46

APPENDIX C

PATTON NETLINK-E1™ MODEL 2701RC

FACTORY REPLACEMENT PARTS

AND ACCESSORIES

Patton Model #

Description

2701RC/D/V........................E1/FE1 CSU/DSU Rack Card, X.21 

Interface w/DB15FS/RJ48C rear card

2701RC/B/B ........................E1/FE1 CSU/DSU Rack Card, RS530\

Interface with DB25F/RJ48C Rear 
Card

2701RC/A/I ..........................E1/FE1 CSU/DSU Rack Card, V.35

Interface with M/34F/RJ48C Rear Card

1001RPEM-RAC

120/240V Rear Power Entry Module

1001RPEM-RAC

120/240V Rear Power Entry Module

1001RPSM-RUI...................120/240V Front Power Supply Module
1001RPEM-RDC.................DC Rear Power Entry Module
1001RPSM-R48A................48V Front Power Supply Module
1001R14P ...........................Rack 14 Slot 2U Chassis Only
1001R14P/R48V .................Rack 14 Slot 2U w/Dual Universal

Input 48VDC Power Supplies

1001R14P/RUIA..................Rack 14 Slot 2U w/Dual Universal

Input 90-260VAC Power Supplies
European Power Cord

1001R14P/RUIC .................Rack 14 Slot 2U w/Dual Universal

Input 90-260VAC Power Supplies

Austrialia Power Cord

1001R14P/RUID .................Rack 14 Slot 2U w/Dual Universal

Input 90-260VAC Power Supplies
UK Power Cord

1001R14P/RUIG .................Rack 14 Slot 2U w/Dual Universal

Input 90-260VAC Power Supplies
India Power Cord

1001R14P/RUIK..................Rack 14 Slot 2U w/Dual Universal

Input 90-260VAC Power Supplies
US Power Cord

1001RCM12548C ...............DB-25/RJ-45 Rear Card
1001RCM13448C ...............M/34/RJ-45 Rear Card
1001CC ...............................Control Card
IM2RC/B..............................RS-530 Interface Rear Card
1180RC DB .........................V.35 Daughter Board
05R16BP440W ...................Single Width Blank Rear Panel, White
05R16FP440W....................Single Width Blank Front Panel, White
0516FPB1 ...........................Single Width Blank Front Panel, Black
0516FPB4 ...........................4-Wide Blank Front Panel, Black
0516RPB1...........................Single Width Blank Rear Panel, Black
0516RPB4...........................4-Wide Blank Rear Panel, Black
056S1..................................Set of 16 #4 pan head screws/washers
10-25M/35M-1.....................Cable, 6 ft, DB-25 male to M/34 male
1010-10 ...............................Terminal Block, 2 Position, Male
07M2701RC ........................User Manual

Summary of Contents for 2701RC



























Reviews: