background image

USER
MANUAL

SALES OFFICE
(301) 975-1000
TECHNICAL SUPPORT
(301) 975-1007
http://www.patton.com

Part# 07M2085-D
Doc# 047033U,
Rev. E
Revised 1/22/08

MODEL 2085

High Speed RS-232
to RS-485 Interface
Converter

C E R T I F I E D

An ISO-9001

Certified Company

Dear Valued Customer,

Thank you for purchasing Patton Electronics products!   We do appreciate

your business.  I trust that you find this user manual helpful.  

We manufacture one of the widest selections of data communications

products in the world including CSU/DSU's, network termination units,
powered and self-powered short range modems, fiber optic modems, interface
converters, baluns, electronic data switches, data-line surge protectors,
multiplexers, transceivers, hubs, print servers and much more.  We produce
these products at our Gaithersburg, MD, USA, facility, and can custom
manufacture products for your unique needs.

We would like to hear from you.  Please contact us in any of the following

ways to tell us how you like this product and how we can meet your product
needs today and in the future.  

Web:               

http://www.patton.com

Sales E-mail:      

[email protected]

Support E-mail:    [email protected]
Phone - Sales      

(301) 975-1000

Phone - Support  

(301) 975-1007

Fax:                   

(301) 869-9293

Mail:               

Patton Electronics Company
7622 Rickenbacker Drive
Gaithersburg, MD  20879   USA

We are committed to a quality product at a quality price.  Patton

Electronics is ISO 9001 certified.  We meet and exceed the highest standards
in the industry (CE, UL, etc.).

It is our business to serve you.  If you are not  satisfied with any aspect of

this product or the service provided from Patton Electronics or its distributors,
please let us know.  

Thank you.

Burton A.Patton
Vice President

P.S.  Please tell us where you purchased this product.

Summary of Contents for 2085





















Reviews: