background image

 

9

 

3.2  RACK CARD INSTALLATION

 

The VLINK modem rack card comprised a front card and a rear card.Do 
the following to install the cards into the rack chassis:

   1. Slide the rear card into the back of the chassis along the metal rails.

   2. Secure the rear card using the supplied metal screws.

   3. Slide the front card into the chassis until you feel resistance as the 

front card engages the rear card. When that happens, 

 

gently 

 

push 

the front card forward until it is fully seated in the card-edge recepta-
cle of the rear card (it should 

 

click

 

 into place).

   4. Secure the front card using the captive fasteners.

 

Note

 

The Model 1001R14 chassis supports “hot swapping” of cards, 

so it is not necessary to power down the rack when you install or 
remove a VLINK modem rack card.

 

Figure 3. 

 

VLINK modem rack card

 

   5. Connect the line interface between the units (refer to section 3.3, 

“Connecting the Twisted-Pair Line Interface” on page 10)

 

Note

 

See Figure 3 for the rack card’s panel arrangements.

VDSL Link

Ether

net

PO

TS/ISDN

1068RC

Ethernet

Port

POTS/ISDN

Port

VDSL Link

RJ-45 interface

VDSL Link

terminal block

Summary of Contents for 1068




























Reviews: