background image

3.2  CONFIGURATION SWITCH SET “S1”

The DIP switches on S1 set data rate, clock source, async./sync.

mode and carrier control method. The default settings are summarized
in Figure 4.

S1-1 through S1-4: Data Rate Setting

Switches S1-1 through S1-4 and  S3-3 are set in combination to

determine the asynchronous and synchronous data rate for the Model
1065RC.

5

6

3.0  CONFIGURATION

This section describes the location and orientation of the Model

1065RC’s configuration switches and provides detailed instructions on
setting each of the switches.

The Model 1065RC uses 24 DIP switches that allow configuration

to an extremely wide range of applications. These 24 DIP switches are
accessible when the card is slid out of the rack chassis. Once config-
ured, the Model 1065RC is designed to operate transparently, without
need for frequent re-configuration: just set it and forget it!

3.1  SWITCH LOCATIONS AND ORIENTATION

The Model 1065RC has three sets of eight switches—S1, S2, and

S3—which are mounted on the PC board (Figure 1). These configura-
tion switches allow you to select data rates, clocking methods, V.52 &
V.54 tests, word lengths, extended signaling rates, async. or sync.
mode, 2- or 4-wire operation, antistream control and input impedance.
As Figure 2 shows, the orientation of all DIP switches is the same with
respect to “ON” and “OFF” positions.

Figure 2. Close-up of DIP switches showing “ON” and “OFF” positions

OFF

ON

Figure 1. Model 1065RC board, showing location of DIP switches 

S3

S2

S1

ON

OFF

OFF

OFF

ON

ON

S1 SUMMARY TABLE

Position

Function

Factory Default

S1-1

Data Rate

On

S1-2

Data Rate

Off

S1-3

Data Rate

Off

S1-4

Data Rate

On

S1-5

Clock Source

On

S1-6

Clock Source

On

S1-7

Async./Sync.

On

Async.

S1-8

Carrier Control

Off

Constantly On

9,600 bps

Internal

}

}

Figure 4. Summary of DIP switch default settings for set S1

DATA RATE SETTINGS  S1-1 THROUGH S1-4 & S3-3

1.2 kbps

ON

ON

ON

ON

1.8 kbps

OFF

ON

ON

ON

1.4 kbps

ON

OFF

ON

ON

3.6 kbps

OFF

OFF

ON

ON

4.8 kbps

ON

ON

OFF

ON

7.2 kbps

OFF

ON

OFF

ON

9.6 kbps

ON

OFF

OFF

ON

SETTINGS

S1-1

S1-2

S1-3

S1-4

OFF

OFF

OFF

OFF

OFF

OFF

OFF

S3-3

Figure  5: Data Rate Settings S1-1 Through S1-4 & S3-3

Summary of Contents for 1065RC

















Reviews: