background image

APPENDIX B

CABLE RECOMMENDATIONS

The Patton Model 1012ARC operates at frequencies of 20kHz or

less and has been performance tested by Patton technicians using
twisted-pair cable with the following characteristics:

Wire Gauge

Capacitance

Resistance

19 AWG

83nf/mi or 15.72 pf/ft.

.0163 Ohms/ft.

22 AWG

83nf/mi or 15.72 pf/ft.

.0326 Ohms/ft.

24 AWG

83nf/mi or 15.72 pf/ft.

.05165 Ohms/ft.

Using or simulating cable with the above characteristics, the

following data rate/distance results were obtained by Patton during
bench tests: 

Data Rate (Bps)

Gauge (AWG) / Distance (Mi)

19

24

26

Up to  38,400

6.0

3.5

2.0

To gain optimum performance from the Model 1012ARC, please

keep the following guidelines in mind:

• 

Always use twisted pair wire—this is not an option.

• Use twisted pair wire with a capacitance of  20pf/ft or less.

• Avoid twisted pair wire thinner than 26 AWG (i.e. avoid AWG

numbers higher AWG numbers than 26)

• Use of twisted pair with a resistance greater than the above 

specifications may cause a reduction in maximum distance 
obtainable.  Functionality should not be affected.

• Many environmental factors can affect the maximum 

distances obtainable at a particular site.  Use the above 
data rate/distance table as a 

general guideline only.

15

APPENDIX C

FACTORY REPLACEMENT PARTS

The Patton Model 1012ARC rack system features interchangeable

rear cards, power cords/fuses for international various operating
environments and other user-replaceable parts.  Model numbers and
descriptions for these parts are listed below:

Patton Model #

Description

1000RPEM..........................120/240V Rear Power Entry Module
1000RPSM-2.......................120/240V Front Power Supply Module
1000RPEM-DC ...................DC Rear Power Entry Module
1000RPSM-48A ..................48V Front Power Supply Module
1000RPEM-V ......................120/240V CE Compliant Rear Power 

Entry Module

1000RPSM-V ......................120/240V CE Compliant Front Power 

Supply Module

0805US ...............................American Power Cord
0805EUR.............................European Power Cord CEE 7
0805UK ...............................United Kingdom Power Cord
0805AUS.............................Australia/New Zealand Power Cord
0805DEN.............................Denmark Power Cord
0805FR ...............................France/Belgium Power Cord
0805IN.................................India Power Cord
0805IS.................................Israel Power Cord
0805JAP..............................Japan Power Cord
0805SW ..............................Switzerland Power Cord

0516FPB1 ...........................Single Width Blank Front Panel
0516FPB4 ...........................4-Wide Blank Front Panel
0516RPB1...........................Single Width Blank Rear Panel
0516RPB4...........................4-Wide Blank Rear Panel

0821R4................................400 mA Fuse (5x20mm)

Littlefuse 239.400 or equivalent

0821R2................................200 mA Fuse (5x20mm)

Littlefuse 239.200 or equivalent

056S1..................................Set of 16 #4 pan head screws/washers

16

Summary of Contents for 1012ARC











Reviews: