background image

 

7.

 

Use a tractor equipped with a Roll-Over Protection System (ROPS) and fasten your seat belt prior 
to starting the engine. 

8.

 

Manufacturer does not recommend usage of tractor with ROPS removed. 

9.

 

Move tractor wheels to widest recommended settings to increase stability. 

10.

 

Do not allow anyone to stand between tongue or hitch and towing unit when backing up to 
equipment. 

11.

 

Make sure all fasteners are tight and installed. 

12.

 

Check for leaks and repair any that are found. 

13.

 

Confirm the tank straps are correctly tightened. 

14.

 

Inspect the tanks making sure lids are secure and the tanks are in working order. 

 

DURING OPERATION 

 

Beware of bystanders, 

PARTICULARLY CHILDREN!

  Always look around to make sure it is safe to 

start engine machine with Helicopter Tanks.  This is particularly important with higher noise levels and 
quiet cabs, as you may not hear people shouting. 
 

NO PASSENGERS ALLOWED!  

Do not carry passengers anywhere on or in the machine with 

Helicopter Tanks. 
 
Keep hand and clothing clear of moving parts. 
 
Do not clean, lubricate, or adjust the machine while it is moving. 
 
When halting operations, even periodically, set tractor or towing unit brakes, disengage PTO, shut off 
engine, and 

remove ignition key. 

 

Be especially observant of operating area and terrain – watch for holes, rocks, or other hidden hazards.  
Always inspect area prior to operation. 
 

 

DO NOT 

operate near the edge of drop-offs or banks. 

 

DO NOT 

operate on steep slopes. An overturn may result. 

 

Operate up and down (not across) intermediate slopes.  Avoid sudden starts and stops. 

       Pick the most level possible route when transporting across fields.  Avoid edges of   

ditches, gullies, and steep hillsides. 

 

Be extra careful when working on inclines. 

 

Avoid overhead wires or other obstacles.  Contact with overhead lines could cause serious injury 
or death. 

 

Avoid loose gravel, rocks, and holes: they can be dangerous for equipment operations or 
movement. 

 

Do not walk or work under raised components or attachments unless securely positioned and 
blocked. 

 

Keep all bystanders, pets, and livestock clear of work area. 

 

Operate towing unit from operators seat only 

 

Never stand alongside of unit with engine running or attempt to start engine and/or operate 
machine while standing alongside of unit. 

 

Never leave running equipment attachments unattended. 

 

As a precaution, always recheck hardware on equipment following every 100 hours of operation.  
Correct all problems.  Follow maintenance safety procedures. 

 

 
 
 
 

Helicopter Tanks

10

Summary of Contents for Helicopter Tanks Series





















Reviews: