1
2
3
4
5
6
Front
Back
LED Indicator
9552 • 110419
Printed in
China
To operate the fan using the remote, press and release the following buttons:
1 - High fan speed
2 - Medium fan speed
3 - Low fan speed
4 - Fan Power: Turns the fan off.
Light Delay Off Mode - Press and hold the fan power button (4) for five seconds, which will turn off light after one
minute. The LED indicator on the remote will flash four times to confirm mode setting.
5 - Light Control:
Dimmable Bulbs
- Tap button to turn lights off and on. Press and hold button to dim or brighten the lights.
Non-dimmable bulbs
- Turns lights on and off.
Note:
The dimmer function does not work with non-dimmable bulbs.
6 - D/CFL Switch: Switch should be set to “CFL” to correspond with standard non-dimmable bulbs; set to “D” for
incandescent and other dimmable bulbs.
Learn
- Syncs remote control to receiver. The remote was synced at the factory. Should it become necessary to re-sync
the remote, turn off the main power, then turn it back on. Within 30 seconds, use a small screwdriver to press and
hold the learn button on the remote for 3 seconds. The fan will turn on and light (if applicable) will blink three times,
signaling a successful synchronization.
OPERATING INSTRUCTIONS
TROUBLESHOOTING
1-YEAR LIMITED WARRANTY
If you have difficulty operating your remote, or have difficulty with installation, please contact Customer Service : 1-877-459-3267, 9 a.m.-5 p.m. Central time.
WARNING:
Ensure the power is turned off to the fan/remote before performing any maintenance.
LED indicator on the remote illuminates, but the remote won’t control the fan. The remote may need to be re-synced.
The remote is synced to the receiver at the factory. Occasionally, power surges can cause the remote to become un-synced. Whenever necessary, follow the syncing instructions
below.
SYNCING INSTRUCTIONS:
Turn off the main power, then turn it back on. Within 30 seconds, press and hold the high and low speed buttons on the remote at the same time for 5
seconds. The LED indicator will flash 3 times, signaling a successful synchronization. Once complete, the fan will start on the low speed with the light (if applicable) off.
The LED indicator on the remote does not illuminate.
The battery most likely needs to be replaced or it is not oriented correctly in the battery compartment. If battery is depleted rapidly, ensure one of buttons is not stuck in the
down position.
The LED indicator stays on.
Ensure one of buttons is not stuck in the down position.
Remote controls more than one fan.
Turn off the power to the fans you don’t want synced. Follow the syncing instructions listed above. Then, turn on the power to the other fans.
Dimming feature does not function.
Ensure the “D/CFL” button in the battery compartment is set to the “D” position and the bulbs are incandescent or other dimmable bulbs.
Fan will not run at high speed.
If you fan has manual pull chains to operate the fan speed, be sure the pull chain is manually set to HIGH SPEED. If your pull chain is set to LOW or
MEDIUM SPEED, the remote will not override the manual pull chain setting.
Light will not turn on.
If you fan has manual pull chains, be sure the light pull chain is set to ON. The remote will not override the manual pull chain setting.
To obtain service, please contact the Service Department:
1-877-459-3267, 9 a.m.- 5 p.m. Central time.
The manufacturer warrants all of its lighting fixtures against defects in materials and workmanship for one (1) year from the date of purchase. If within this period the product
is found to be defective, take a copy of the bill of sale as a proof of purchase and the product in its original carton to the place of purchase. The manufacturer will, at its option,
repair, replace or refund the purchase price to the consumer. All costs of installation and removal of the fixture is the responsibility of the consumer. This warranty does not cover
fixtures becoming defective due to misuse, accidental damage or improper handling and/or installation and specifically excludes liability for direct, incidental or consequential
damages. As some states do not allow exclusions of limitations on an implied warranty, the above exclusion and limitation may not apply. This warranty gives you specific rights
and you may also have other rights which may vary from state to state.
