Restrict Field Service to the Following
RECHARGING THE BATTERY
CHECKING THE FUEL CARTRIDGE
REPLACING THE FUEL CARTRIDGE
CLEANING/REPLACING THE AIR FILTER
CLEARING A JAM
CLEANING THE TOOL (See cleaning manual)
Attempts to go beyond these procedures could result in
serious personal injury or damage to the Cordless Finish
Nailer and voiding the warranty.
There are certain problems you may encounter when you
are using the Cordless Finish Nailer that you will be able
to correct on the work site. The following field service
procedures are the only service procedures you should
attempt. Anything else that may appear wrong with the
Cordless Finish Nailer should only be diagnosed and
repaired by a fully trained service technician. If you have
any reason to believe that your problem is beyond the
service procedures in this manual, contact your Paslode
®
representative immediately.
Servicing
Fuel Cartridge Check
DANGER
Wear safety glasses when performing this test. Never
perform this test near an open flame or sparks, while
smoking, or where the fuel may get into your eyes.
If fuel is not released with each operation of the metering
valve, this indicates that there is no more fuel left in the
cylinder and it must be replaced. Dispose of the empty fuel
cartridge.
(see page 10.)
Clearing a Jam
An occasional problem you may encounter is a jammed
s
s
e
l
d
r
o
C
e
h
t
f
o
n
g
i
s
e
d
e
u
q
i
n
u
e
h
t
f
o
e
s
u
a
c
e
B
.
r
e
n
e
t
s
a
f
Finish Nailer, clearing a jammed fastener is easy:
1. Remove the battery.
2. Pull the latch, releasing front guide. Pivot front guide
forward.
3. Clear jam, and push driver blade back up to its normal
position.
4.
Battery Check
Periodically check on the battery indicator light (the light
in the handle) of the Cordless Finish Nailer. When
encountering a problem, the first step should always be
to make sure the battery has enough charge to operate
the tool.
When the work contacting element is depressed on work
piece, the fan motor will turn on and the blinking green
indicator light will turn solid green. If the indicator light blinks
red or glows red, recharge the battery.
DANGER
Never attempt any maintenance of a Paslode Cordless
tool without first removing the fuel cell and battery.
Maintenance should be started only after the tool is
completely inoperative.
CHECKING THE ENERGY LEVEL OF THE
BATTERY
If the Cordless Finish Nailer's fan operates and the indica-
tor light is green, but the tool will not cycle or does not
drive fasteners completely, check the fuel cartridge. With
the fuel cartridge out of the tool, check to see if the
cartridge still contains fuel and that the metering valve is
working. To determine if there is any fuel left in the fuel
cartridge, hold in the upright position and simply place the
metering stem against a solid object, and gently push
about three or four times. A small amount of fuel should
be released each time.
Close front guide and latch it. Check that the work
contacting element moves freely.
C R O MO
NO D H
Z RD US
O LY N
E TI A
D AR A O
AVO N
U E A
D U ONS
I U E S
I Z
N US M N
LE M
D D E P
I E R ON R
P CT P
T NTR N
R DE C
ID N S
E L ION
A ARD
N V R U
E N EX
O VE A
M SPH RE
OO E HA
U T OUL
G I E
M S
OL
A O N
B S AN
E S MU T W
AR Y AND H
R NG P O
EC ON
HA C NFO
M TO
N STA D
DS
A
A L
N E M
AL
O
O
R
R
D
S UME
O L S
L A S O
D D N
W L A W
Y F E A F
S E ER
AD A
L O O
R O E
S G
NG
N G
U D S L
N C I
N
