background image

9

OPERATOR TROUBLESHOOTING

 PROBLEM

            

CORRECTIVE ACTION 

Fasteners will not drive completely into wood.

Fasteners penetrate properly during normal 
operation, but won't drive fully at faster speeds.

Fasteners drive too deeply into wood.

Fastener jams in nose of tool.

Tool skips during operation - no fasteners are driven
from time to time.

Tool operates, but no fasteners are driven.

Air leaks at cap when tool is connected to air.

Adjust the depth of drive adjustment (retract length).

Increase air pressure (do not exceed 120 psi).

Increase air flow to tool — use larger air lines
(3/8 inch ID minimum).

Adjust the depth of drive adjustment (extend length).

Reduce air pressure.

Open front guide latch, release jammed fastener, 
and close latch securely.

Check magazine for proper fasteners. Magazine 
follower should slide freely. Clean as needed to 
remove debris.

Make sure correct fasteners are being used. Use 
fasteners that meet Paslode

®

 specifications only.

Increase air flow to tool -- use larger air lines
(3/8 ID minimum).

Adjust work contacting element where available.

Check magazine for proper fasteners. Fasteners 
should slide freely with no follower pressure.

Open front guide latch and check for jams or 
debris in the nose area. Clear as necessary 

Increase air pressure (do not exceed 120psi).

Tighten cap screws.

Disconnect the tool when performing
repairs or clearing jams.

CAUTION

Summary of Contents for T250S-F16P





















Reviews: