background image

6

Precision Placement Driving

 

■  

Grasp the tool handle firmly and place the bottom of the work 

contacting element firmly against the workpiece until it is com-

pletely depressed.

■  

Squeeze the trigger to drive the fastener.

■  

Lift the tool from the workpiece.

■  

Repeat the procedure for the next fastener.

Successive (Bounce) Driving

 

■  

Grasp the handle firmly.

■  

Squeeze the trigger and move the tool along the workpiece 

with a bouncing motion, depressing the work contacting element 

at the points where you want to insert a fastener.

■  

Keep the trigger depressed and continue to bounce the work 

contacing element against the workpiece, positioning the tool 

above as carefully as possible.

■  

When the desired number of fasteners have been driven, 

release the tool trigger to avoid unintentional fastener discharge.

TOOL OPERATION - 

continued

Loading of Nails

 Step 1 - Grasp the handle firmly. 

 Step 2 - Insert one or two strips of nails into the 

  

               rear of the magazine.

 

Step 3 - Pull the follower to the rear of the 

 

 

 

magazine until it is engaged behind the 

  

 

nails.

The tool is manufactured with a (Silver) sequential 

trigger installed.  

Sequential Operation

 - 

(Silver

 

Trigger)

The sequential operating trigger prevents successive 

or “bounce” driving.

■  

Depress the work contacting element and hold it  

against the work surface before pulling the trigger.

■  

After each fastener is driven, completely release  

the trigger and lift the tool from the work surface.

Grommet

Trigger Pin

Sequential Lever

Sequential 

Trigger

Sequential 

Actuator

#501039

Contact Trip (Bounce) Trigger Operation-

(Orange Trigger)

Grommet

Trigger Pin

Bottom Trip Lever

Contact

Trigger

The 

trigger

 

kit

 

(#501048)

 

allows

 

successive

 or 

“bounce”

 

driving.

#501048

WARNING

Do not clamp or hold the trigger with 
anything other than your hand.

Summary of Contents for PowerMaster Pro F-350P

































Reviews: