2
Introduction and Warranty
Paslode
Angled Finish Nailer Operating
Manual
This manual is intended to acquaint you with the Paslode
Cordless Angled Finish Nailer. Unlike other power fastening
tools, the Paslode Angled Finish Nailer is powered by an
internal combustion linear motor. In simpler terms, your
Paslode Angled Finish Nailer is powered by a motor similar
to the one that powers an automobile. The Paslode Angled
Finish Nailer ignites a fuel and air mixture to produce the
energy to drive the motor, which in turn drives the fastener.
The Paslode Angled Finish Nailer is totally self-contained.
It carries its own fuel supply and battery, along with a supply
of fasteners.
For ease of use, this manual is divided into sections (see
Contents). Each section of the manual is written with you,
the tool operator, in mind. We have left out many of the
technical terms so that you can easily understand how to get
the maximum performance from your Paslode Angled Finish
Nailer, and how to avoid damaging the tool or injuring
yourself. But, to accomplish this, we need you to do two
things:
1. READ THE MANUAL FROM COVER TO COVER
BEFORE USING THE TOOL.
2. FOLLOW ALL INSTRUCTIONS IN THE MANUAL.
The Paslode Finish nailer should be handled like other
power fastening tools that you use. Like most tools, when
used improperly injury could result . If you are going to
allow others to use the Paslode Finish nailer, it is your
responsibility to make sure that they also read and comply
with the instructions in this manual before attempting to
operate the tool.
Should you have questions about the Paslode Finish
nailer, or wish to obtain additional copies of this manual,
please contact your Paslode
®
representative. The space
below is provided so that you may record your
representative's name, address, and telephone number.
For the nearest Paslode representative call 1-800-
682-3428
Name
Address
City
State
Zip
Telephone Number
Paslode Cordless Warranty and Limitations
Paslode warranties that new Impulse
®
power fastening tools,
parts and accessories will be free from defects in material and
workmanship for the period shown below, after the date of
delivery to the original user.
ONE-YEAR LIMITED WARRANTY
A one-year warranty will apply to all parts, except those listed
below as normal wearing parts, or parts which are specifically
covered by an extended warranty.
FIVE-YEAR EXTENDED LIMITED WARRANTY
A five-year warranty will apply to all molded nylon parts:
•
Cap and Grille
•
Handle Halves and Actuator
•
Trigger
90-DAY LIMITED WARRANTY
A 90-day warranty applies to the following parts, which are
considered normal wear parts:
•
Bumper
•
Driver Blades
•
O-Rings
WARRANTY STATEMENT
Paslode's sole liability hereunder will be to replace any part or accessory
which proves to be defective within the specific time period. Any replacement
part or accessory provided in accordance with this warranty will carry a
warranty for the balance of the period of warranty applicable to the part it
replaces. This warranty does not apply to part replacement required due
to normal wear.
This warranty is void on any tool which has been subjected to misuse,
abuse, accidental or intentional damage, use with fasteners, fuel, batteries,
or battery chargers not meeting Paslode specification, size, or quantity,
improperly maintained, repaired with other than genuine Paslode
replacement parts, damaged in transit or handling, or which, in Paslode's
opinion, has been altered or repaired in a way that affects or detracts from
the performance of the tool.
PASLODE MAKES NO WARRANTY, EXPRESSED OR IMPLIED,
RELATING TO MERCHANTABILITY, FITNESS, OR OTHERWISE,
EXCEPT AS STATED ABOVE, and Paslode's liability AS STATED ABOVE
AND AS ASSUMED ABOVE is in lieu of all other warranties arising out of,
or in connection with, the use and performance of the tool, except to the
extent other wise provided by applicable law. PASLODE SHALL IN NO
EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, OR CONSEQUENTIAL
DAMAGES, INCLUDING, BUT NOT LIMITED TO, DAMAGES WHICH
MAY ARISE FROM LOSS OF ANTICIPATED PROFITS OR
PRODUCTION, SPOILAGE OF MATERIALS,, INCREASED COST OF
OPERATION, OR OTHERWISE.
