background image

5      IM50S COILMASTER MANUAL

FUEL CELL SAFETY

FUEL CELL SAFETY

WARNING 
EXPLOSION/FIRE HAZARD 

Read all instructions before using  
or handling the fuel cell. 

Keep the fuel cell away from heat, sparks 
and open flame. Do not smoke when 
handling or operating tool or fuel cell. 

Exposure to temperatures above 49°C 
(120°F) may cause the fuel cell to burst, 
releasing flammable gas. 

Sunlight can raise the inside temperature 
of an unventilated motor vehicle or storage 
container to above 60°C (140°F). 

Never puncture or attempt to open 
the fuel cell; it is non-refillable. Never 
incinerate, reclaim or recycle the fuel cell. 
Dispose of used cell responsibly.

Never smoke while installing the fuel  
cell or operating the tool. 

Never inhale the spray. 
Store fuel cell(s) in well-ventilated areas 
only. 

Keep out of the reach of children. 

Liquid gas can cause injury in the event  
of contact with the skin or eyes. 

FUEL CELL CHECK
Paslode Impulse fuel cells are marked with 
a “Best Use Before” date on the bottom of 
the can. For maximum performance use 
fuel before the “Best Use Before” date.

COLD WEATHER OPERATION

Fuel combustion can be adversely affected at extreme low 
temperatures. Ensure that the tool battery and fuel cell are 
above the minimum oper ating temperature of 7°C (20°F) 
before use.

The fuel cell is an aerosol product corresponding to the 
2008/47/EC regulations. It contains:

•  Liquefied hydrocarbon gases (butane, propane, 

propylene).

•  A lubricant to maximise the tool durability.
When the fuel is used there will always be some 
propellant left inside the cartridge. The fuel cell is always 
pressurized. Its contents are extremely flammable. The 
fuel cell is not reusable. 

FUEL CELL DISPOSAL

Dispose of all empty fuel cells responsibly. Remember to 
dispose of these fuel cells where they will not be crushed, 
punctured, burned or found by children.

STORAGE 

Stores and showrooms must comply with building  
regulations. All local instructions corresponding to fire  
regulations must be followed. 

•  Where possible, store fuel at a stable temperature in 

the range 7°C to 25°C. Do not expose to temperatures 
exceeding 49°C.

•  Do not use tools that emit flames, sparks or reach high 

temperatures in the vicinity that fuel cells are stored. 

•  Do not store in designated thoroughfares, hallways or 

stairwells. 

•  Store in a well-ventilated area. 
•  Fuel cells must not be displayed in shop windows. 
•  Storage with pyrotechnic products is not permitted. 

FIRST AID 

•  Direct contact with liquid gas may cause burns or  

frostbite. 

•  In case of inhalation remove the person to fresh air,  

and encourage breathing. Should the casualty become  
unconscious, or breathing does not quickly return to  
normal, summon urgent medical assistance.

•  If gas gets into the eyes they should be flushed out with 

copious amounts of water. Skin contamination should 
be removed with soapy water. 

If symptoms persist, seek medical assistance.

Summary of Contents for COILMASTER IM50S





















Reviews: