background image

Shaking Tower Kit

 ME

-

7018

8

012

-

16515A

Tower Construction

Items Needed: Flat F4 Beams (24), Truss Set Screws (28), Floors (5), Ground Floor Structure (1)

Step One: Align the Flat F4 

Beams of the Ground Floor 

Structure with the bottom ver

-

tical slots of the Half Round 

Connectors on the First Floor 

Step Two: Use Truss Set 

Screws to attach the First 

Floor to the Flat F4 Beams. 

Step Three: Use four Truss 

Set Screws to attach four Flat 

F4 Beams to the top vertical 

slots of the Half Round Con

-

nectors on the First Floor.

Step Four: Add the Second 

Floor to the top of the Flat F4 

Beams of the First Floor. 

Attach four Flat 4 Beams to 

the Second Floor. 

Use the same process to add 

the Third Floor to the Fourth 

Floor and the Fifth Floor to 

the Fourth Floor. NOTE, do 

not add any Flat F4 Beams to 

the Fifth Floor. 

ME-7566: Required 

Additional Item

Notice on page 1 that the 

illustration of the Shaking 

Tower shows slotted masses 

on the Ground Floor and 

each of the Tower Floors.

The PASCO ME-7566 Large 

Slotted Mass Set consists of 

nine iron disks of 0.5 kg each 

and a hanger of 1.5 kg. 

Stack three disks on the cen

-

ter of the Ground Floor Struc

-

ture. Put one disk on each of 

the Floors. The circular step 

on the top of the disk fits in 

the hole in the Foam Floor.

Ground Floor 

Structure

First Floor 

Structure

Bottom 

Vertical 

Slot

Flat F4 Beam

Bottom 

Vertical 

Slot

Top 

Vertical 

Slot

Flat F4 Beam

First Floor 

Structure

Summary of Contents for ME-7018














Reviews: