ParTech OxyTechw2 GAL Instruction Manual Download Page 4 | Manualshive

Page: 4 / 28

ParTech OxyTechw2 GAL Instruction Manual Download Page 4

OxyTechw² GAL Instruction Manual

8.4.3 M:0x Set Cal (100.0 %SAT) or M:0x Set Cal (25.0 ºC)................................................................17
8.4.4 M:0x Averaging............................................................................................................................ 17
8.4.5 M:0x Remove............................................................................................................................... 17
8.4.6 M:0x Display Position.................................................................................................................. 17
8.4.7 M:0x Restore Defaults................................................................................................................. 17
8.4.8 M:0x Set Pressure....................................................................................................................... 18
8.4.9 M:0x Set Salinity.......................................................................................................................... 18

9 Calibration and Testing................................................................................................................................ 19

9.1 Temperature........................................................................................................................................ 19

9.1.1 Overview...................................................................................................................................... 19
9.1.2 Calibrate Temperature................................................................................................................. 19

9.2 OxyTechw² GAL.................................................................................................................................. 20

9.2.1 Zero Calibration (Service Mode Only)..........................................................................................20
9.2.2 Zero Checking............................................................................................................................. 21
9.2.3 SPAN Calibration......................................................................................................................... 21

10 Maintenance.............................................................................................................................................. 22

10.1 General cleaning................................................................................................................................ 22

10.2 Inspection.......................................................................................................................................... 22

10.3 OxyTechw² GAL Refurbishment........................................................................................................ 22

11 Spares....................................................................................................................................................... 24

12 Technical Support...................................................................................................................................... 25

12.1 Returning Equipment for Repair........................................................................................................25

13 Technical Specification – OxyTechw² GAL................................................................................................26

13.1 Physical............................................................................................................................................. 26

13.2 Electrical............................................................................................................................................ 26

13.3 Measurement..................................................................................................................................... 26

13.4 Mounting Options............................................................................................................................... 26

Page 4 of 28

224083IM-Issue 04 20/03/2018

«
...
2
3
4
5
6
...
»

Summary of Contents for OxyTechw2 GAL





























Reviews:

No comments