13
12
NOTE:
main power and water supply before calling Parmco Appliances.
If all the lights begin to blink that indicates the machine is out of order, please turn off the
Forgot to Add a Dish?
A forgotten dish can be added any time before the detergent cup opens.
2. After the spray arms stop working, you can open the door completely.
3. Add extra dishes.
4 Close the door, the dishwasher will work after ten seconds.
1. Open the door a little to stop the washing.
Open the door carefully. Hot steam may escape when the door is opened!
- Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around
15 minutes before removing from the appliance.
- Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In
this way they will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper
basket onto the dishes in the lower one.
Changing the Programme during use
Premise: A cycle that is underway can only be modified if it has only been running for a short time.
Otherwise, the detergent may have already been released, and the appliance may have already
drained the wash water. If this is the case, the detergent dispenser must be refilled (see the section
entitled " Fill in the Detergent " ).
1. Press the “Power” button to cancel the programme.
2. Turn on it again and you can change the programme to the desired cycle setting (see the section
entitled "Starting a wash cycle. . . " ).
NOTE:
If you open the door when washing, the machine pauses and warning alarm rings, LED1 and
LED2 flash. When you close the door, the machine will keep on working after 10 seconds.
The 6 programme lights show the state of the dishwasher:
a) All program lights off --> stand by
b) One of the program lights on --> cycle running
c) One of the program lights blinking --> pause
NOTE:
A click could be heard when the door is closed perfectly.
When the washing is over, you can shut off the switch by pressing "Power" button.
Starting a wash cycle...
Draw out the lower and upper basket, load the dishes then:
1. push them back. It is recommended to load the lower basket first, then the upper one (see
section "Loading the Dishwasher"). Add detergent and rinse aid if empty.
2. Insert the plug into the socket. The power supply is 220-240V AC 50 Hz, the specification of
the socket is 12 A 250 VAC.50 Hz.
Turning on the Appliance
6. Starting a Washing Programme
Wash cycle table
Program
Cycle Selection
Information
Description
of Cycle
Detergent
Pre/main
Running
Time
(min)
Energy
(kWh)
Water
(L)
Intensive
Heavy
Rinse
Rapid
Soak
For the heaviest soiled loads,
such as pots, pans, casserole
dishes and dishes that have
been sitting with dried food
on them for a while.
For heavy soiled loads,
such as pots, plates, glasses
and lightly soiled pans.
A shorter wash for lightly
soiled loads that do not
need drying.
To rinse dishes that you
plan to wash later that day
Pre-wash(40 C)
Main wash(55 C)
Rinse
Hot rinse(65 C)
Drying
Main wash(60 C)
Rinse 1
Rinse 2
Hot rinse(65 C)
Drying
Main wash(45 C)
Rinse
Hot rinse(49 C)
Drying
Pre-wash
Hot rinse(70 C)
Drying
Main wash(40 C)
Hot rinse(49 C)
Pre-wash
5/25g
5/25g
5/25g
15g
145
135
112
67
50
8
1.20
1.15
0.73
0.75
0.50
0.01
15.5
15.0
11.8
7.5
7.5
4.0
Normal
(AS/NZS 2007.1)
For dishes that need to be
rinsed and dried only
NOTE:
Make sure that the water supply is turned on to full pressure. Close the door, press the"Power"
button, Press the "program." button to select a desired "Wash cycle". (See the section entitled
"Wash Cycle Table".)
Ensure the door is properly closed.
For normally soiled loads,
such as pots, plates, glasses
and lightly soiled pans.
Standard daily cycle.
LED1 LED2 LED3 LED4 LED5 LED6
We recommend opening the door slightly 50mm to assist in drying the dishes
after every wash.
