Humidty sensor
In the movement process, this device is used for induction clothing humidity, it means that
it must be carried on cleaning. Major cause of clean is must scour out the calcium oxide
boiler which on the sensor surface up. Clean the sensor in the tumbler (See picture).
Clean the filter drawer
Press the button to open the cover.
Unlock the fixer.
Pull out the filter drawer.
Clean lint, fiber and cotton raveling on the filter cloth by hand or with a soft piece of cloth.
When you notice a layer that may lead clogging on the filter cloth, please clean the layer by
washing in warm water. Let the filter cloth dry thoroughly before installing back the filter drawer.
Wash the filter drawer sponge by hand to remove the fiber and lint on the surface. After
washing the sponge. squeeze it by hand and remove the excess water. Well-dry the sponge
before storing it.
Clean the evaporator
Clean the lint accumulated on the fins of the evaporator located behind the filter drawer
with a vacuum cleaner or a soft brush. You can also clean by hand provided that you
wear protective gloves.
It is recommended to clean it at least twice every month.
Never attempt to clean with bare hands.Evaporator fins can harm your hand.
If you are unable to identify or solve the problem, contact our service centre. Before telephoning,
make a note of the model, serial number and purchase date of your machine: the Service Centre
will require this information.
This appliance must be earthed. In case of failure or damage, earth can provide a minimum resistance to
reduce the possibility of electric shock. The power cord has grounding wire with device and power cord
with plug. Plug must be inserted into a properly installed and grounded socket(in accordance with all local
rules and standards).
A separate earth is required by some local rules. In that case, you need buy grounding wire, clips and screws.
Caution
!
Removing transport safety packaging foam
Water discharge
Procedure
Earth note
IMPORTANT: The appliance must not built-in.
Unpacking
All packing must be removed before using the appliance.
Check accessory
Open the accessory bag and check the accessories.
Care must be taken to ensure that the appliance does not stand on the electrical supply cable.
Any electrical work required to install this appliance should be carried out by a qualified electrician or
competent person.
Should the appliance be moved, it must be transported vertically.
650
220/50
Power(left-on mode)(W)
Power(off mode)(W)
Programme time at full load(min)
0.48
290
595X630X850
Ambient temperature range( )
℃
5
35
~
8.0
Energy efficient gear
Daily
0.48
Lint and fibre that could not be captured by the lint filter are blocked in the filter drawer behind the cover.
Clean the filter drawer after each drying process. There is a two-level filter in the filter drawer. The first
level is the filter drawer sponge and the second level is the filter cloth.
IMPORTANT :
If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation,
a charge will be made even if the appliance is under guarantee.
It’s not necessary to dischargr the condensed water to the tank, it can be drained out directly.
change drainpipe
Pull out the water pipe by means of the arrow direction ,Then install the drainpipe.
Such as the pilers can be used if it is difficult to do.
Before use the machine, the packaging foam must be removed from the drum.
1.Open the loading door.
2.Pull off adhesive strips from inside machine on top of drum.
3.Remove the two packaging foam from the machine.
Check across the corner
When press on the edge, the machine should not shake up and down. (please check two direction) when
press on the top frame (across the corner), the dryer shakes, need to re-adjust the adjustable feet.
Do not put stacks of blanket or a rope on the floor, which could generrate some heat and affect the
machine running.
two packaging foam
drainpipe
manual
Quantity
It is dangerous to alter the specifications or attempt to modify this product in any way.
Malfunction
Possible Cause
Solution
Dryer does
not work
Drying results
unsatisfactory
Drum light does
not work(option)
Drying cycle ends
shortly after
programme starts.
"END" light
illuminated.
Drying cycle lasts
an unusually long
time
Mains plug is not plugged in.
Loading door is open.
Have you pressed the button?
Wrong programme selected.
Filter clogged.
Incorrect volume of laundry.
The sediment on humidity sensor.
Light bulb is defective.
Not enough washing loaded or
washing load is too dry for selected
programme.
Load volume is too big.
Select a different programme the next time
you dry(see "Drying Programme "section).
Clean lint filter.
Observe recommended loading volumes.
Washed hunidity sensor surface.
Replace light bulb.
Select higher drying level(e. g. Heavy instead
of Strong)
Reduce load volume.
Plug in at main socket.
Close loading door.
Press the button again.
DR8WHP
9
