background image

17

Scope of the warranty

The device has been manufactured according to strict quality guidelines and tested diligently 
before delivery. The warranty applies to material or fabrication defects. This warranty does not 
cover product parts that are subject to normal wear and tear and therefore can be considered 
as parts subject to wear and tear or for the damage to fragile parts, e.g switch, batteries or those 
made of glass.
This warranty is void if the product is damaged, not used or maintained properly. All the 
instructions provided in the operating manual must be followed exactly for proper use of the 
product. The purpose of use and actions which  are advised or warned against must necessarily 
be avoided. 
 The product is intended solely for private use and not for professional use. The warranty is void 
in case of misuse or improper handling, use of force and changes that have not been carried out 
by our authorised service centre.

Processing a warranty case

To ensure quick processing of your issue, please follow the below instructions:
•  Please be ready with the sales receipt and the product number (e.g. IAN 12345) as proof or 

purchase for all queries. 

•  You can refer the product number from the type label, an engraving, on the cover sheet of 

your operating instructions (below left) or as sticker on the back or lower side.

•  If functional or other defects occur, first call or email the following service department. 
•  You can then send a product recorded as defective postage free along with the sales receipt 

and information about where the defect lies and when it has occurred, to the service centre 
address provided to you. 

This and many other manuals, product videos and software can be downloaded at  
www.lidl-service.com

Service

  
Walter Werkzeuge Salzburg GmbH 
E-Mail: [email protected] 
Tel.: 00800 925 837 88 

IAN 373546_2104

 

Supplier:

Please note that the following address is not a service centre address. Please contact the 
above-mentioned service centre first.  
Walter Werkzeuge Salzburg GmbH  
Gewerbeparkstr. 9 
5081 Anif, Austria

Summary of Contents for WWS-GLK9-Y02



















Reviews: