36
PSFS 250 A1
BG
Работа с уреда
Използвайте уреда само по предназначение и
с оригинални части/принадлежности.
Употребата на части или други принадлежности,
различни от препоръчаните в това ръководство-
то за потребителя, може да причини опасност
от нараняване. Използвайте единствено изцяло
развити и неповредени удължители с капацитет
от минимум 5 A.
ПРЕДУПРЕЖДЕНИЕ!
►
Не използвайте този инструмент за изряз-
ване в близост до инсталации или отвори
с тоководещи електрически кабели или в
стени, зад които е възможно да са поло-
жени тоководещи електрически кабели.
Битът може да проведе ток в инструмента,
а това е свързано с опасност от токов
удар за работещия с уреда.
–
Отвийте автоматичния предпазител
или извадете предпазителя, за да
изключите от напрежение съответната
електрическа верига.
ПРЕДУПРЕЖДЕНИЕ!
►
Винаги дръжте инструмента за пластмасо-
вия корпус и носете защитни очила при
работа с инструмента.
Включване/Изключване
Включване:
♦
Натиснете бутона за включване/
изключване .
Изключване:
♦
Отпуснете бутона за включване/
изключване .
Настройка на честотата на въртене
♦
Завъртете регулатора на честотата на върте-
не надясно, за да увеличите честотата на
въртене.
♦
Завъртете регулатора на честотата на върте-
не наляво, за да намалите честотата на
въртене.
Смяна на инструмента
УКАЗАНИЕ
►
Използвайте комбинираната фреза само
с принадлежности с диаметър на опашка-
та ø 4,8 mm.
♦
Задръжте натисната блокировката на
шпиндела .
♦
Отвийте затегателната гайка с гаечния
ключ чрез завъртане обратно на часовни-
ковата стрелка.
♦
Сменете инструмента.
♦
Задействайте блокировката на шпиндела,
затегнете затегателната гайка с помощта
на гаечния ключ .
Битове:
Включените в окомплектовката на доставката
битове покриват следните области на прило-
жение:
Универсална фреза (високопроизводителна
бързорежеща стомана) :
Подходяща за: дърво, плочи от дървесни частици,
пластмаса, алуминий и стоманена ламарина
Фреза за изработване на канали (високопро-
изводителна бързорежеща стомана) :
Подходяща за: дърво, плочи от дървесни части-
ци, пластмаса
Шлифовъчни ленти :
Подходящи за: шлифоване на дърво
УКАЗАНИЕ
►
За рязане на стенни керамични плочки и/
или обработка на метални листове/леки
метали използвайте съответните принад-
лежности от специализираната търговска
мрежа.
Монтиране на шлифовъчни ленти
♦
Поставете шлифовъчната лента отгоре
върху затегателния дорник за шлифовъчни
ленти . Затегнете винта на затегателния
дорник за шлифовъчни ленти , за да фик-
сирате шлифовъчната лента .
Summary of Contents for PSFS 250 A1
