![background image](http://html1.mh-extra.com/html/parkside/kh-3049-drill-sharpener/kh-3049-drill-sharpener_manual_4072040008.webp)
9
GB/IE/CY
should always make sure that no-one is at risk
from them and that no combustible materials
are located in the proximity of the area of work.
WARNING!
RISK OF INJURY!
Use the
ON/OFF
switch
4
to switch the grinder off in
the event of a power failure or when pulling out
the mains plug. This prevents the grinder restarting
by accident, which could cause injury to you.
Never operate the grinder if the power
cable or mains plug is damaged.
Grinding stones must be carefully
stored and handled according to the
manufacturer’s instructions.
Make sure that the grinding tools are
appropriate in line with the instructions
of the manufacturer.
Check the grinding stone before using
it;
do not use any broken, cracked or other-
wise damaged goods.
Make sure that a grinding tool is cor-
rectly fitted and fastened before using
it.
Place the grinder in a safe place and allow
it to run idly for 30 seconds. Stop it immediately
if considerable oscillations occur or if defects
are observed. If this occurs, check the machine
to find out the cause.
Original accessories /
Attachments
Use only the accessories and attachments de-
tailed in the operating instructions. The use of
inserted tools or accessories other than those
recommended in the operating instructions
could lead to you suffering an injury.
Use
Sharpening a drill
Insert the drill into the smallest suitable drill
guide
11
on the drill sharpener.
Press the ON / OFF switch
4
into position “I”
to switch on the device.
Turn the drill under slight pressure loosely and
quickly to and fro between the left and right
stops about 10 times (with small drills about
5 times).
This sharpens the first cutting edge of the drill.
Pull the drill out, turn it through 180° (horizontally)
and insert it again until it meets the sharpening
stone.
Turn the drill in the same way as for grinding
the first edge. This sharpens the second cutting
edge of the drill.
If necessary repeat whole process until both
cutting edges of the drill are sharp.
Press the ON / OFF switch
4
into position “0”
to switch off the device.
NOTE:
The cutting edges of the drill must be of the
same length.
Replacing the sharpening stone
WARNING!
DANGER OF INJURY!
Al-
ways pull the mains plug is out of the socket before
doing any work on the device. Replace the sharp-
ening stone if it is worn or damaged. You will need
a Phillips screwdriver for this procedure.
Remove the four rubber feet
5
from the under-
side of the device, refer to Fig. A. If necessary
use a small slotted head screwdriver or similar
device as an aid for doing this.
Using a Phillips screwdriver, screw out the four
motor unit screws
6
under the rubber feet,
refer to Fig. B.
Remove the motor unit
3
and set it to one side.
Screw out the four sharpening stone cover
screws
7
, refer to Fig. C.
Remove the sharpening stone cover
8
. Remove
the sharpening stone.
Clamp the sharpening head push rod
9
in a
vice. Using a 20 mm open spanner, release the
threaded connection holding the sharpening
stone on the shaft.
NOTE! LEFT-HANDED THREAD - TURN
CLOCKWISE TO RELEASE!
Mount the new sharpening stone on the shaft
with flattened edge at the bottom. Insert the
sharpening stone into the device.
General safety instructions / Use
Summary of Contents for KH 3049 DRILL SHARPENER
