background image

10  GB/CY

… / Disposal / Translation  of  the  original  declaration  of  conformity / Manufacturer

Operation / Maintenance  and  cleaning / Service / Warranty

  

Turn the exhaust air aperture 

1

 to guide the 

exhaust airflow in the desired direction.

  

After finishing work, disconnect the device from 
the compressor.

  

Removing jammed fasteners

  

If a staple or nail gets jammed in the magazine 
slot, immediately disconnect the compressed 
air supply.

  

Open the magazine 

6

 as described in the 

chapter “Loading the magazine“.

 

 Open the face plate 

11

 by pulling the face 

plate quick clamping lever 

12

 in the direction 

of the trigger lock 

9

.

  

Remove the jammed fastener.

  

Close the face plate 

11

 by pulling the face 

plate quick clamping lever 

12

 in the direction 

of the exhaust air aperture 

1

.

   Close the magazine 

6

 of the compressed air 

tacker as described in the chapter “Loading the 
magazine“.

  

Maintenance and cleaning

  

RISK OF INJURY!

 Be absolutely certain to 

disconnect the device from the compressed air 
source before cleaning or maintaining it.

  

Maintenance

Lubrication with oil mister 
NOTE:

 As a treatment stage after the pressure re-

ducer, an oil mister provides continuous and optimum 
lubrication of the compressed air tacker. An oil mis-
ter gives off fine drops of oil into the airflow and so 
guarantees regular lubrication.

  

Install the oil mister after the (filter) pressure re-
ducer. To do so, insert the nipple of the oil mister 
into the quick-release coupling of the (filter) 
pressure reducer.

  

Then connect the compressed air device to the 
quick-release coupling provided for it.

Manual lubrication
NOTE:

 If you do not have an oil mister, lubricate the 

device each time after driving about 5000 fasteners.

 

 Apply 1–2 drops of special compressed air oil 
into the threaded nipple 

4

 of the compressed 

air tacker.

  

Then press the trigger 

2

 several times. 

ATTENTION: 

Be certain not to use too much 

oil; otherwise oil could leave the mouth with the 
fastener and potentially damage the workpiece.

  

Cleaning

  

Do not use any sharp objects to clean the device. 
Do not allow any liquids to enter the device. 
Otherwise the device could be damaged.

  

Clean the device regularly, preferably always 
immediately after finishing work.

  

Use a dry cloth to clean the housing. Under no 
circumstances should you use petrol, solvent or 
cleaners which attack plastic.

  

After each use, pack the compressed air tacker 
in the carrying case it was delivered with to 
protect it from dirt.

  

Service

  

 Have your fastener 

driving tool repaired only by qualified 
specialist personnel using original man-
ufacturer parts only.

 This will ensure that 

your fastener driving tool remains safe to use.

Note: 

Spare parts not listed (e.g. carbon brushes, 

switches) can be ordered through our call centre.

  

Warranty

The warranty for this appliance is for 3 
years from the date of purchase. The ap-
pliance has been manufactured with care 
and meticulously examined before deliv-
ery. Please retain your receipt as proof 
of purchase. In the event of a warranty 
claim, please make contact by telephone 

Summary of Contents for 96899






















































Reviews: