![background image](http://html1.mh-extra.com/html/parkside/93548/93548_operation-and-safety-notes_4156402009.webp)
9
GB
General power tool safety warnings
General power tool safety warnings
marked on the power tool.
Accessories
running faster than their rated speed can break
and fly apart.
d)
Wheels must be used only for recom-
mended applications. For example:
do not grind with the side of cut-off
wheel.
Abrasive cut-off wheels are intended
for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
e)
Always use undamaged wheel flanges
that are of correct diameter for your
selected wheel.
Proper wheel flanges sup-
port the wheel thus reducing the possibility of
wheel breakage.
f)
Do not use worn down reinforced
wheels from larger power tools.
Wheels
intended for a larger power tool are not suita-
ble for the higher speed of a smaller tool and
may burst.
g)
The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
In-
correctly sized accessories cannot be adequately
guarded or controlled.
h)
The arbour size of wheels and flanges
must properly fit the spindle of the
power tool.
Wheels and flanges with arbour
holes that do not match the mounting hardware
of the power tool will run out of balance, vibrate
excessively and may cause loss of control.
i)
Do not use damaged wheels. Before
each use, inspect the wheels for chips
and cracks. If power tool or wheel is
dropped, inspect for damage or install
an undamaged wheel. After inspecting
and installing the wheel, position your-
self and bystanders away from the
plane of the rotating wheel and run
the power tool at maximum no load
speed for one minute.
Damaged wheels
will normally break apart during this test time.
j)
Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hear-
ing protectors, gloves and shop apron
capable of stopping small abrasive or
workpiece fragments.
The
eye protection
must be cap-able of stopping flying debris gen-
erated by various operations. The dust mask
or respirator must be capable of filtrating par-
ticles generated by your operation. Prolonged
exposure to high intensity noise may cause
hearing loss.
k)
Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protec-
tive equipment.
Fragments of workpiece or
of a broken wheel may fly away and cause in-
jury beyond immediate area of operation.
l)
Hold the power tool by insulated grip-
ping surfaces only, when performing
an operation where the cutting acces-
sory may contact hidden wiring or its
own cord.
Cutting accessory contacting a
“live” wire may make exposed metal parts of
the power tool “live” and could give the oper-
ator an electric shock.
m)
Position the cord clear of the spinning
accessory.
If you lose control, the cord may
be cut or snagged and your hand or arm may
be pulled into the spinning wheel.
n)
Never lay the power tool down until
the accessory has come to a complete
stop.
The spinning wheel may grab the surface
and pull the power tool out of your control.
o)
Do not run the power tool while car-
rying it at your side.
Accidental contact
with the spinning accessory could snag your
clothing, pulling the accessory into your body.
p)
Regularly clean the power tool’s air
vents.
The motor’s fan will draw the dust
inside
the housing and excessive accumulation of
powdered metal may cause electrical hazards.
q)
Do not operate the power tool near
flammable materials.
Sparks could ignite
these materials.
r)
Do not use accessories that require
liquid coolants.
Using water or other liquid
coolants may result in electrocution or shock.
Summary of Contents for 93548
Page 3: ...A 0 1 C D E B 3 1 2 16 9 1 4 6 7 11 10 12 15 9 5 3a 14 14 8 13...
Page 4: ......
Page 14: ...14...
Page 34: ...34...