![background image](http://html1.mh-extra.com/html/parkside/104027/104027_operation-and-safety-notes_3934382007.webp)
7
GB
Noise and vibration data:
Measured values for noise are determined in accor-
dance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level:
74.33 dB(A)
Sound power level:
85.33 dB(A)
Uncertainty K:
3 dB
Wear ear protection!
The total vibration (vector sum of three directions) is
calculated in accordance with EN 60745:
Sanding:
Vibration emission value a
h
= 2.590 m / s
2
,
Uncertainty K = 1.5 m / s
2
The vibration level specified in
these instructions was measured in accordance with
an EN 60745 standardised measurement process
and can be used to compare equipment. The vibra-
tion emission value specified can also serve as a
preliminary assessment of the exposure.
The vibration level will change according to the ap-
plication of the electrical tool an in some cases may
exceed the value specified in these instructions. Re-
gularly using the electric tool in such a way may
make it easy to underestimate the vibration.
Note:
If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
General safety advice for
electrical power tools
Read
all the safety advice
and instructions!
Failure
to observe the safety advice and instructions may
result in electric shock, fire and / or serious injury.
Keep all the safety advice and instructions
in a safe place for future reference!
The term “electrical tool” used in the safety advice
refers to electrical tools powered by mains electricity
(by means of a mains lead) and electrical tools pow-
ered by rechargeable batteries (without a mains lead).
1.
Workplace safety
a)
Keep your working area clean and well
lit.
Untidy or poorly lit working areas can lead
to accidents.
b)
Do not work with the device in poten-
tially explosive environments in which
there are inflammable liquids, gases or
dusts.
Electrical power tools create sparks,
which can ignite dusts or fumes.
c)
Keep children and other people away
while you are operating the electrical
tool.
Distractions can cause you to lose con-
trol of the device.
2.
Electrical safety
a)
The mains plug on the power tool (or
on the power supply) must fit the mains
socket. Never modify the plug in any
way. Never use adapter plugs with
earthed power tools.
Unmodified plugs
and the correct sockets reduce the risk of elec-
tric shock.
b)
Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrig-
erators with any part of your body.
There is an increased risk of electric shock if
your body is earthed.
c)
Keep the device away from rain or
moisture.
Water entering an electrical device
increases the risk of electric shock.
d)
Do not use the mains lead for any pur-
pose for which it was not intended, e.g.
to carry the device, to hang up the de-
vice or to pull the mains plug out of
the mains socket. Keep the mains lead
away from heat, oil, sharp edges or
moving parts of the device.
Damaged or
tangled mains leads increase the risk of elec-
tric shock.
Introduction / General safety advice for electrical power tools
Introduction
Summary of Contents for 104027
