background image

JINCNS05 RevF 27/04/12 
 

General Guidance 

It  is  important  that  your  stove  is  correctly 

installed  as  Parkray  Stoves  cannot  accept 

responsibility  for  any  fault  arising  through 

incorrect use or installation. 

 

These  instructions  cover  the  basic  principles  to 

ensure  satisfactory  installation  of  the  stove, 

although detail may need slight modification to 

suit particular local site conditions.  

 

The  installation  must  comply  with  current 

Building  Regulations,  national  and  European 

standards,  Local  Authority  byelaws  and  other 

specifications  or  regulations  as  they  affect  the 

installation of the stove.  

 

The Building Regulations requirements may also 

be 

met 

by 

adopting 

the 

relevant 

recommendations  in  the  current  issues  of 

British Standards BS 8303 and BS EN 15287-1. 

Competent Persons Scheme 

Parkray  Stoves  recommend  that  this  stove  is 

installed  by  a  member  of  an  accredited 

competent persons scheme e.g. HETAS. 

 

If the installer is not a member of a competent 

persons  scheme,  it  is  a  legal  requirement  to 

notify  your  local  building  control  body  in 

advance of any work starting. 

CO Alarms 

Building  regulations  require  that  whenever  a 

new  or  replacement  fixed  solid  fuel  or 

wood/biomass  appliance  is  installed  in  a 

dwelling,  a  carbon  monoxide  alarm  must  be 

fitted in the same room as the appliance. 

 

Further  guidance  on  the  installation  of  the 

carbon  monoxide  alarm  is  available  in  BS  EN 

50292:2002 and from the alarm manufacturer’s 

instructions. 

Provision of an alarm must not be considered a 

substitute  for  either  installing  the  appliance 

correctly  or  ensuring  regular  servicing  and 

maintenance  of  the  appliance  and  chimney 

system. 

Health and Safety Precautions 

Special  care  must  be  taken  when  installing  the 

stove such that the requirements of the Health 

and Safety at Work Act are met. 

Handling 

Adequate  facilities  must  be  available  for 

loading, unloading and site handling.  

Fire Cement 

Some  types  of  fire  cement  are  caustic  and 

should  not  be  allowed  to  come  into  contact 

with  the  skin.  In  case  of  contact,  wash 

immediately with plenty of water.  

Asbestos 

This  stove  contains  no  asbestos.  If  there  is  a 

possibility  of  disturbing  any  asbestos  in  the 

course of installation then please seek specialist 

guidance  and  use  appropriate  protective 

equipment.  

Summary of Contents for CONSORT SLIMLINE 5



















Reviews: