manualshive.com logo in svg

ParkerBrand PPWP-2000, Owner'S Manual

Share
Download
ParkerBrand PPWP-2000 Owner'S Manual Download Page 27

52

53

TROUBLESHOOTING

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

ENGINE WILL NOT START

Fuel valve is 'OFF'

Move fuel valve lever to 'ON'

Choke 'OPEN'

Move choke lever to 'CLOSED' unless engine is warm.

Engine switch is 'OFF'

Turn engine switch is 'ON'

Out of fuel

Refuel.

Stale fuel (Stored without draining)

Drain stale fuel and replace with fresh fuel

Spark Plug faulty

Remove spark plug clean, gap, or replace.

Flooded engine

Remove spark plug, dry and reinstall spark plug.

Clogged fuel filter, Carburettor

malfunction, valves stuck etc

Take engine to a qualified mechanic. Replace or repair faulty parts.

ENGINE LACKS POWER

Air filter clogged

Check air filter, clean or replace.

Stale fuel (Stored without draining)

Drain stale fuel and replace with fresh fuel.

Clogged fuel filter, Carburettor

malfunction, valves stuck etc

Take engine to a qualified mechanic. Replace or repair faulty parts.

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

NO PUMP OUTPUT

Pump not primed

Prime pump.

Hose collapsed, cut or punctured

Replace suction hose.

Strainer not completely submerged

Submerge the strainer completely under water.

Air leak at connector

Replace sealing washer if missing or damaged. Tighten connectors and 

clamp. Use PTFE tape on the threads of ports.

Strainer clogged

Clean debris from strainer

Excessive head

Relocate pump and/or hoses to reduce head

LOW PUMP OUTPUT

Hose collapsed, damaged, too long or diam-

eter too small

replace suction hose/Replace discharge hose..

Air leak at connector

Replace sealing washer if missing or damaged. Tighten connectors and 

clamp. Use PTFE tape on the threads of ports.

Strainer clogged

Clean debris from strainer

Marginal head

Relocate pump and/or hoses to reduce head

If this does not solve your problem, please contact the ParkerBrand customer service department 

01507 499198.

Summary of Contents for PPWP-2000



































Reviews:

No comments

Brands by name

Popular brands

Load more brands