manualshive.com logo in svg

ParkerBrand PPWP-2000, Owner'S Manual

Share
Download
ParkerBrand PPWP-2000 Owner'S Manual Download Page 15

28

29

PRE-OPERATION

PRE-OPERATION

Remove the dipstick by turning it in an anti-

clockwise direction.

2

1

LOCATE OIL FILL/DIPSTICK

Locate the oil fill/dipstick near the base of the 

machine. 

REMOVE DIPSTICK

'HIGH'

LEVEL

'LOW'

LEVEL

Take out the dipstick and clean with a cloth. 

Put the dipstick back into the oil filler tube and then 

remove it again.

Do not screw it in all the way back in when doing this.

If the oil is below the ‘L’ level on the dipstick, fill the oil 

reservoir to the ‘H’ level on the dipstick.

Replace the oil filler cap.

We recommend the use of 4 stroke SAE30 oil.

(SKU:

 PLO-4STR)

 is available separately from 

www.parkerbrand.com

3

CHECK DIPSTICK

4

ADD OIL

'FULL'

NOTE: This pump is not supplied with any oil within the engine, there is only trace left from testing.

WARNING! You will damage the engine beyond repair if you start it without adding oil to the engine first.

WARNING! To carry out this procedure, place the pump on level ground with the engine switched off.

WARNING! Take care not to touch any hot parts of the pump when checking the oil level.

Summary of Contents for PPWP-2000



































Reviews:

No comments

Brands by name

Popular brands

Load more brands