Parker Sporlan Division SCS-PB Series Installation And Operating Instructions Manual Download Page 6

Page 6

 – Bulletin 100-50-11.1

4. Parameters

The following tables describes the parameters that are available for this controller. The parameters can be 
accessed by connecting to the controller by using a mobile device such as a smart phone. See the Setup 
Section for more details on how to connect to the controller.

Parameter

Description

Range

Date/Time

Current date and time

Dates/Times

Superheat Target

The desired superheat

5°F to 45°F

2.78°C to 25°C

Refrigerant

Specifies what refrigerant is being used

See list of available refrigerants

Identification - Rack

Identifies the compressor rack  

the coil is connected to

4 characters, alphanumeric

Identification - Lineup

Identifies the lineup the coil is connected to

4 characters, alphanumeric

Identification - Case ID

Identifies the specific case/coil being  

controlled by the controller

4 characters, alphanumeric

Pressure Transducer - Range

Specifies the range of the pressure  

transducer being used

0 to 1000 PSI

0 to 68.95 bar

Pressure Transducer - Type

Specifies the pressure transducer type

Absolute or Gauge

Pressure Transducer - Offset

Offset from zero applied to the pressure sensor

-20 to 20 PSI

-1.38 to 1.38 bar

Coil Outlet Thermistor - Type

Specifies the type of thermistor used  

The controller comes with a 10K thermistor

2K
3K

10K (default)

Coil Outlet Thermistor - Offset

Offset from zero applied to the thermistor

-10°F to 10°F

-5.56°C to 5.56°C

Stepper Type - Number of Steps

Specifies the number of steps the stepper 

valve has – only applies to SCS-SB

100 to 10,000 steps

Stepper Custom Polarity

Specifies the valve polarity – 

only applies if “Custom” is chosen as  

the stepper type on the SCS-SB

Unipolar or Bipolar

Stepper Custom Step Rate

Specifies the valve movement rate in steps/

second – only applies if “Custom” is chosen  

as the stepper type on the SCS-SB

30 to 400

Refrigerants available to use with the SCS controller:

R-22

R-134a

R-402A

R-404A

R-407A

R-407C

R-410A

R-417A

R-422A

R422D

R-507A

R-744

R-245fa

R-438A

R-401B

R-408A

R-508A

R-508B

R-407F

R-434A

R-444B

R-448A

R-450A

R-449A

R-452A

R-513A

R1336mzz

R-427A

R-422C

Note:

 Additional refrigerants may be added over time. If your refrigerant is not listed, a new firmware package with additional refrigerants may be 

available. Please contact Sporlan Application Support or your local Sporlan Sales Representative for information.

Summary of Contents for Sporlan Division SCS-PB Series











Reviews: