Parker PSUP Series Installation Manual Download Page 10

Introduction

 

PSUP Mains module

 

10 

192-120147N9 PSUP Manual 2019-06

1.6 

Conditions of utilization for CE-conform operation 

- Industry and trade -

The  EC  guidelines  for  electromagnetic  compatibility 

2014/30/EU

  and  for  electrical

 

operating devices for utilization within certain voltage limits 

2014/35/EU

 are fulfilled

 

when the following boundary conditions are observed:

Operation of devices only in the state in which they are delivered. 

A mains filter is required in the mains input line if the motor cable exceeds a certain 
length. Filtering can be provided centrally at the system mains input or separately 
for each axis system.  

  

 

The following mains filters are available for independent utilization: 

Use of the devices in the industrial area (limit values class C3 in accordance 

with EN 61800-3) 

  

Device: PSU 

Limit value 

class 

Reference: Axis system 

with motor cable 

Mains filter 

Order No.: 

P10 

C3 

< 6 x 10 m 

NFI03/01 

P10 

C3 

< 6 x 50 m 

NFI03/02 

P20 

C3 

< 6 x 50 m 

NFI03/03 

P30 

C3 

< 6 x 50 m 

NFI03/03 

  

 

unshielded: 

Connection length: Connection between mains filter and device: 

< 0.5 m 

shielded 

< 5 (fully shielded on ground - e.g. ground of control cabinet) 

Connect the filter housing and the device to the cabinet frame, making sure that the 
contact area is adequate and that the connection has low resistance and low 
inductance. 
Never mount the filter housing and the device on paint-coated surfaces! 

 

Signal lines and power lines should be installed as far apart as possible.

 

Signal lines should never pass close to excessive sources of interference
(motors, transformers, contactors etc.).

 

Do not place mains filter output cable parallel to the load cable.

Make sure to use only the accessories recommended by Parker 

Connect all cable shields at both ends, ensuring large contact areas! 

This is a product in the restricted sales distribution class according to EN 61800-3. 
In a domestic area this product can cause radio frequency disturbance, in which 
case the user may be required to implement appropriate remedial measures. 

Mains filter: 

Grounding: 

Cable installation: 

Accessories: 

Warning: 

Summary of Contents for PSUP Series





























Reviews: