Parker LORD Use And Maintenance Manual Download Page 22

UM1004 | MRO-00011      05/21 Rev.0      DCO-016875 

22 

 

Figure 10.  Sealing Sub Section View 

 

 

Figure 11.  Sealing Sub Exploded View 

 

 

 

 

 

 

Values stated in this document represent typical values as not all tests are run on each lot of material produced. For formalized product specifications for specific product end uses, contact the Customer 

Support Center. 
Information provided herein is based upon tests believed to be reliable. In as much as Parker LORD has no control over the manner in which others may use this information, it does not guarantee the 

results to be obtained. In addition, Parker LORD does not guarantee the performance of the product or the results obtained from the use of the product or this information where the product has been 

repackaged by any third party, including but not limited to any product end-user. Nor does the company make any express or implied warranty of merchantability or fitness for a particular purpose 

concerning the effects or results of such use. 
WARNING — USER RESPONSIBILITY. FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, 

PERSONAL INJURY AND PROPERTY DAMAGE. 
This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation by users having technical 

expertise. 
The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance, maintenance, safety and 

warning requirements of the application are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning the product in the current 

product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors. 
To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the user, the user is responsible for determining 

that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems. 

Parker LORD 

Engineered Materials Group 

Oil & Gas Engineering 
111 LORD Drive 

Cary, NC 27511-7923 

USA 

phone +1 855 796 1595 

[email protected] 

www.lord.com/OilandGas 

Summary of Contents for LORD























Reviews: